Bosch PSM VENTARO 1400 Manual Original página 20

Ocultar thumbs Ver también para PSM VENTARO 1400:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 34
OBJ_BUCH-39-004.book Page 20 Tuesday, July 21, 2009 2:15 PM
20 | English
Vacuuming Function
The vacuum cleaner 4 can be used to vacuum
dry, non-hazardous materials. The supplied mul-
ti sander 1 can be used in this operating mode.
For vacuum cleaning, the dust bag must be in-
serted. For this, see chapter "Inserting/Replac-
ing a Dust Bag".
Align the arrows on the vacuum hose 3 and the
vacuum hose connection 8 and insert the vacu-
um hose into the vacuum hose connection. You
will hear a distinct "click" when the vacuum
hose locks in the vacuum hose connection.
You can connect the multi sander 1 or any of the
accessories mentioned on the accessories page
to the vacuum hose 3.
Blower Function
The vacuum cleaner 4 can easily be converted to
a blower in no time at all.
Remove the closing cover with blower filter 12
from the holder 10 and insert the adapter for
the blower connection 11 in its place.
Align the arrows of the vacuum hose 3 and the
adapter for the blower connection 11 and insert
the vacuum hose into the adapter. You will hear
a distinct "click" when the vacuum hose locks in
the adapter.
Do not point the blower jet at persons or an-
imals. The blown-out air is warm.
Removing the Vacuum Hose
To remove the vacuum hose 3, rotate the hose a
little and pull it off.
Connecting the Multi Sander
(see figure F)
The supplied multi sander 1 can be used in the
"Extraction" operating mode of the vacuum
cleaner 4.
The closing cover with blower filter 12
should be inserted in the holder 10. The
blower filter cleans the blown out air.
Insert the vacuum hose 3 into the vacuum hose
connection of the multi sander 22.
1 609 929 S60 | (21.7.09)
Ensure that a dust bag is inserted in the vacuum
cleaner when sanding.
To remove the vacuum hose 3, rotate the hose a
little and pull it off.
Replacing the Sanding Sheet
(see figure G)
When attaching a new sanding sheet, remove
any dust or debris from the sanding plate 24
(e. g. with a brush).
To ensure optimum dust extraction, pay atten-
tion that the punched holes in the sanding sheet
match with the holes in the sanding plate.
The sanding plate 24 is fitted with Velcro back-
ing for quick and easy fastening of sanding
sheets with Velcro adhesion.
Before attaching the sanding sheet 25, free the
Velcro backing of the sanding plate 24 from any
debris by tapping against it in order to enable
optimum adhesion.
The multi sander is equipped with 2 sanding
sheets. Depending on their condition of wear,
these can also be changed individually.
Use the multi sander only when both sand-
ing sheets are attached.
Only use sanding sheets with the same
grain size.
Position the sanding sheet 25 flush alongside
one edge of the sanding plate 24, then lay the
sanding sheet onto the sanding plate and press
firmly.
To remove the sanding sheet 25, grasp it at one
of the tips and pull it off from the sanding plate
24.
Sanding sheets of the Bosch Delta Sander can
be used.
Sanding accessories, such as fleece pads/pol-
ishing cloth pads, are attached to the sanding
plate in the same manner.
Bosch Power Tools

Publicidad

Tabla de contenido
loading

Tabla de contenido