Helpful Hints - DeWalt DCS355 Traducido De Las Instrucciones Originales

EngLIsh
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired cut depth as shown in figure J.
3. Secure the guide in place by turning the depth/cut
adjustment knob 14 clockwise. To release the guide turn
the depth/cut adjustment knob counterclockwise.
Cut Guide
This feature allows you to more accurately track a marked
cut line.
1. Insert the guide arm 7 as shown in figure K into the slots on
the left and right sides of the guide block
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired length as shown in figure L.
3. Secure the guide in place by turning the depth/cut
adjustment knob 14 clockwise. To release the guide turn
the depth/cut adjustment knob counterclockwise.
nOTE: The guide arm can also be placed in the guard assembly
vertically in order to set the height off a cut. Refer to figure M.
Attaching the Dust Extraction Adaptor
(Fig. Q)
The Dust Extraction Adaptor allows you to connect the tool to
an external dust extractor, either using the AirLock™ system
(DWV9000-XJ), or a standard 35 mm dust extractor fitment.
1. Attach the dust extraction adaptor
13 in to the accessory side mount slots
nOTE: The dust extraction adaptor can be attached to either
side of the tool.
2. Insert screw and washer
15
adaptor 17 and tighten with the supplied hex key
OPERATION
Instructions for Use (Fig. N, O)

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Ensure switch is fully OFF before installing
the battery.
1. Install the battery pack.
2. To turn the tool ON, hold it as shown in figure N and press
the variable speed trigger
nOTE: The further the trigger switch is depressed the faster
the tool will operate. If in doubt about the proper speed
for your operation, test the performance at low speed and
gradually increase until a comfortable speed is found.
3. To turn the tool OFF, release the variable speed trigger
Lock on/off Button (Fig. O)
The tool can be locked off by fully depressing the lock on/off
button shown in figure O.
4
36
.
6
by inserting the tabs
17
5 .
into the dust extraction
21
16 .
1 .
1
For more comfort in extended use applications, the lock
on/off button 4 can lock the trigger trigger
depressed position.
LED Worklight (Fig. P)
The LED worklight 2 will activate when the trigger is depressed.
It will automatically shut off following a short period of time
once the trigger is released.
Proper Hand Position (Fig. N)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires the tool to be held as shown in
figure N.
Using the Dust Extraction Adaptor with the
Sanding Platen (Fig. R)
1. Attach the dust extraction adaptor
the Dust Extraction Adaptor.
2. Attach the sanding platen
Installing/Removing Accessories.
3. Attach sanding sheet as described under Installing/
Removing Sanding Sheets.
Using the Dust Extraction Adaptor with
Plunge Cutting Accessory (Fig. S)
1. Attach the dust extraction adaptor. Refer to Attaching the
Dust Extraction Adaptor.
2. Push dust extraction arm
dust extraction adaptor
3. Attach plunge cutting blade as described under Installing/
Removing Accessories.
4. Adjust the dust extraction arm

Helpful Hints

• Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sanding finish.
• Do not start sanding without having the sandpaper
attached to sanding platen.
• Use coarse grit paper to sand rough surfaces, medium grit
for smooth surfaces and fine grit for the finishing surfaces. If
necessary, first make a test run on scrap material.
• Excessive force will reduce the working efficiency and cause
motor overload. Replacing the accessory regularly will
maintain optimum working efficiency.
• Do not allow the sandpaper to wear away, it will damage
.
the sanding pad.
• If the tool overheats, especially when used at low speed,
set the speed to maximum and run it with no load for 2–3
minutes to cool the motor. Avoid prolonged usage at very
low speeds. Always keep the blade sharp.
1 in the
17 . Refer to Attaching
as described under
23
19 into the lower aperture of the
17 .
19 for best results.