Handle Adjustment - Chicco urban plus Manual De Instrucciones

your child inside it, even if the parking brake is engaged.
WARNING: After engaging the parking brake, make sure
the brakes are properly enabled on both rear wheels.
SWIVEL WHEELS
38. It is recommended to use the wheels in the fixed mode
on particularly changeable surfaces. The use of the wheels
in the swivel mode is recommended in order to increase
the control of the stroller on a normal road surface To en-
gage the front swivel wheels, push the front button down-
ward with your foot as shown in fig. 38.
To engage the fixed wheels, press the button with your
foot once again. On fixed mode, all the wheels will remain
locked in straight position.
WARNING: Both wheels must always be locked or un-
locked at the same time.

HANDLE ADJUSTMENT

The stroller features a handle that can be adjusted in height,
according to the user's needs.
39. It can be adjusted to 4 different positions by pressing
the release button located on the centre of the handle (Fig.
39).
After switching from one position to the other, make sure
the automatic locking mechanism is properly engaged.
RAIN COVER
The stroller is equipped with a rain cover.
WARNING: Use the raincover only after purchasing the
"Colour Pack'' and assembling the hood. The rain cover
cannot be used on the stroller without the hood; it may
represent a suffocation hazard for the child. When the rain
cover is fitted on the stroller, never leave it exposed to di-
rect sunlight with the child inside, as the temperature will
rise considerably.
40. To secure the rain cover, completely open the stroller's
hood and wrap the raincover around the external tube of
the backrest. To complete the assembly, also wrap the op-
posite side of the raincover around the tube in the foot area
(fig. 40). After use, hang the raincover to dry (if it is wet) be-
fore folding and storing it away out of the reach of children.
WARNING: Use only the supplied rain cover.
COLOUR PACK (to purchase separately)
List of components:
HOOD
A hood can be fitted on the stroller (available in the Colour
Pack, to purchase separately).
The seat features two joints positioned on the sides of the
backrest that allow the securing of the hood.
41. To secure the hood, introduce the fastening system into
the joints as shown in (fig. 41).
42. Then, secure the fabric part to the hood using the zip
located on the seat frame, around the backrest. (Fig. 42).
WARNING: The hood must be fixed on both sides of the
stroller. Ensure that the hood is correctly secured into position.
43. To remove the hood, open the zip of the hood's fab-
ric part completely and press the buttons located inside
the hood's joints; then pull the hood upwards (Fig. 43).
Reducer cushion
To use it during the early months of your child's life, use the
seat insert sold with the "Colour Pack. " The seat insert must
be assembled in stroller configuration.
To properly position the safety belts on the stroller's back-
rest, refer to the paragraph "USE OF THE SAFETY BELTS
IN STROLLER CONFIGURATION'' .
45. At this point, thread the belts in the relative slots located
on the insert's backrest. Repeat the same operation for the
waist belt and the crotch strap as shown in fig. 45.
COMFORT KIT
46. The "Colour Pack" includes a comfort kit containing 2
shoulder strap pads (A), a crotch strap cover pad (B) (Fig.
46).
47. To assemble, thread the shoulder straps in the slots as
shown in (Fig. 47) making sure to leave the vertical seam
facing outward. The shoulder straps can be adjusted ac-
cording to your child's size.
48. Slide the crotch strap into the slot in the material as seen
in Fig. 48.
LEGCOVER / PRAM APRON
49. This component (Fig. 49A) can be used in two different
ways: as legcover in stroller configuration (Fig. 49B) and as an
50. To secure it, wrap it around the structure, threading it
under the bar and then fasten it to the frame using the ex-
ternal and internal press stud buttons (fig. 50A-50B).
FOLDING THE STROLLER
To fold the stroller, adjust the handle in the lowest position
and leave the front wheels unlocked.
It is possible to close the stroller in two different modes:
without the seat or keeping the seat fastened to the frame.
Folding the stroller without seat
51. To remove the seat, press the grey buttons located near
the seat's joints (Fig. 51).
52. To close the stroller, slide button 1 and then press but-
tons 2 and 3 (Fig. 52).
Folding the stroller with seat
53. Close the seat by pulling the sliding buttons behind the
seat tube upwards (fig. 53), and then push it forward until it
reaches the most compact position (fig. 53 A – 53B).
54. Close the stroller as described in step 52. The stroller is
now closed with the seat fastened to the frame (fig. 54).
WARRANTY
The product is guaranteed against any conformity defect
in normal conditions of use as provided for by the instruc-
tions for use.
The warranty shall not therefore apply in the case of dam-
ages caused by improper use, wear or accidental events.
For the duration of warranty on conformity defects please
refer to the specific provisions of national laws applicable in
the country of purchase, where provided.
23