Vimar Eikon 20135 Guia De Inicio Rapido página 2

Eikon Arké
20135 19135
Dimmer 230 V~ 50 Hz for: 40-500 W incandescent lamps, 40-300 VA electronic transfomers,
10-200 W CFL lamps, 3-200 W LED lamps and LED electronic transfomers, control and regu-
lation with built-in push button or from NO peripheral push buttons, MASTER function, minimum
power control, visible in darkness, grey. Not for Isoset enclosures.
IMPORTANT: Lamps controllable from a single MASTER or SLAVE dimmer must all be
the same. All controllable loads must be declared DIMMERABLE by the manufacturer.
Check the type of compatible dimmering on the lamp package: LE (Leading Edge) or TE
(Trailing Edge). Where not specified, the lamp works in both modes, at the discretion of
the installer; choose the type of dimmering that ensures the best lamp.
Dimmering with Leading Edge mode
CHARACTERISTICS
• ON, OFF and dimmering with built-in buttons or normal non-lit buttons.
• Soft start: ensures gradual lighting from zero to maximum or preset lighting levels. This way the
life of a lamp is increased by reducing stress on the filament and prevents light flash.
• Flash start: used with compact fluorescent lamps, ensures that the lamps are switched on
correctly, reducing any difficulties to a minimum.
• Soft end: slowly brings the load down from on to off.
• Leading Edge mode: used with incandescent lamps, compact fluorescent lamps and LED
compatible lamps, as well as L-type electronic transformers
• Tailing Edge mode: used with compatible loads such as fluorescent lamps, LED lamps or
C-type electronic transformers .
C
• Protection against short-circuit when turning on together with flashing blowout detector.
• Overheating protection with flashing blowout detector.
• MASTER-SLAVE function: paying attention not to exceed maximum power controllable by
each dimmer. A MASTER device can have up to 3 SLAVE devices.
• It should be used in dry, dust-free places at a temperature between 0 °C and +35 °C.
• For installations with 2 dimmers in the same box the loads controllable by each dimmer should
be reduced so that their total does not exceed the values indicated above.
CONNECTIONS
• The connection should be made together with a fuse box with quick-acting fuse with high
breaking capacity type F2,5AH 250 V~.
• Control and dimmering with built-in button or more points with NO buttons in parallel. Do not
use NO buttons with pilot light.
NOTE: THE ON/OFF BUTTON IS CONNECTED TO THE CABLE NEUTRAL.
• In the 2-wire connection of the adapter load must be positioned as close as possible to the
lamp and connected in parallel to it.
• For correct operation, the length of each connection between the MASTER and SLAVE dim-
mers or the NO buttons may not exceed 100 m.
• Press the connection conductors to the bottom of the box to prevent them from coming into
contact with the dimmer body.
STANDARD COMPLIANCE
BT directive
EMC directive
EN 60669-2-1 standard.
Viale Vicenza, 14 - 36063 Marostica VI - Italy
Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188
Fax (Export) +39 0424 488 709
www.vimar.com
Idea Plana
16559 14135
Dimmering with Trailing Edge mode
.
L
3-WIRE CONNECTION
L
20135-19135
16559-14135
20416
P
19416
16460
14416 L
Button ON/OFF
N
Controllable loads
40 - 500 W
10 - 100 W (max 5 lamps)
3 - 100 W (max 5 lamps)
40 - 300 W
(max 3 transformers
Power supplies
max 10 power supplies
01874-01875
Lamps 02662 max 10 lamps
2-WIRE CONNECTION
L
20135-19135
16559-14135
20416
19416
16460
14416 L
P
Button ON/OFF
N
Controllable loads
*
10 - 40 W (max 2 lamps)
*
3 - 40 W (max 2 lamps)
*
may need charging adapter 01873 connected in parallel to the lamp.
SETTING
Remove the upper button.
N
LE TE
40 - 300 W
10 - 200 W (max 10 lamps)
3 - 200 W (max 10 lamps)
40 - 300 W
) (max 5 transformers
L
Not applicable
Not applicable
The 2-wire connection should
only be used to replace regu-
lators in existing electrical
systems where it is not 'this
the neutral wire in the box of
the dimmer.
LE TE
40 - 400 W 40 - 200 W
10 - 40 W (max 2 lamps)
3 - 40 W (max 2 lamps)

Increases the
minimum

Decreases the
minimum
Flash start
TE
switch on for max. 1
second then taken to the
set brightness
LE
Soft start
gradually switched on to the
set brightness
)
C