Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
2.2. SAFETY AT THE WORKPLACE
a)
Make sure the workplace is orderly and well
lit. A messy or poorly lit workplace may lead to
accidents. Try to anticipate what may happen,
observe what is going on and use common sense
when working with the device.
b)
Do not use the device in an explosion hazard zone,
for example in the presence of flammable liquids,
gasses or dust. The device generates sparks which
may ignite dust or fumes.
c)
Upon discovering damage or irregular operation,
immediately switch the device off and report it to
a supervisor without delay.
d)
If there are any doubts as to the correct operation
of the device, contact the manufacturer's support
service.
e)
Only the manufacturer's service point may repair the
device. Do not attempt any repairs independently!
f)
If a fire starts, use solely powder or carbon dioxide
(CO
) fire extinguishers suitable for use on live
2
devices to put it out.
REMEMBER! When using the device, protect children
and other bystanders.
2.3. PERSONAL SAFETY
a)
Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b)
To prevent the device from accidentally switching
on, make sure the switch is on the OFF position
before connecting to a power source.
c)
Note: The metal parts of the lid and the housing may
be hot and may cause skin burns.
2.4. SAFE DEVICE USE
a)
Do not use the device if the ON/OFF switch does not
function properly (does not switch the device on and
off). Devices which cannot be switched on and off
using the ON/OFF switch are hazardous, should not
be operated and have to be repaired.
b)
When not in use, store in a safe place, away from
children and people not familiar with the device,
who have not read the user manual. The device may
pose a hazard in the hands of inexperienced users.
c)
Maintain the device in a good technical state. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of
the device. If damage is discovered, hand over the
device for repair before use.
d)
Keep the device out of the reach of children.
e)
Device repair or maintenance should be carried out
by qualified persons, only using original spare parts.
This will ensure safe use.
f)
To ensure the operational integrity of the device, do
not remove factory fitted guards and do not loosen
any screws.
g)
It is forbidden to move the fryer with hot oil! The oil
can maintain a high temperature even for 6-7h..
h)
Do not turn the fryer "upside down", it may cause
damage to it.
i)
It is forbidden to switch the appliance on if the bowl
is not filled with oil.
8
3. USE GUIDELINES
The fryer is exclusively designed to fry food.
Do not use the fryer to:
•
heat other substances or objects;
•
warm up liquids containing sugar, sweeteners, acids,
bases or alcohols;
•
warm or warm up flammable, noxious, particularly
volatile, or any other toxic substances.
The user is liable for any damage resulting from
nonintended use of the device.
3.1. DEVICE DESCRIPTION
PLEASE NOTE! This product's view can be found on
the last page of the operating instructions (pp. 25).
1.
thermostat
2.
power light
3.
thermostat light
4.
ON/OFF switch
5.
Timer
6.
tap with release valve
7.
handle with basket
8.
lid
3.2.PREPARING FOR USE
APPLIANCE LOCATION
The temperature of the environment must not exceed
45°C and the relative humidity should not exceed 85%.
Ensure good ventilation in the room in which the device
is used. The distance between the back of the appliance
and the wall should be at least 20 cm, a minimum distance
between the sides of the device and the walls should be
at least 10 cm on each side and 35 cm between the top
of the device and the ceiling. Keep the device away from
hot surfaces. Operate the device on flat, stable, clean,
refractory and dry surfaces out of the reach of children and
people with mental disabilities. Install the device making
sure that constant access to the main plug is ensured. The
power cord connected to the appliance must be properly
grounded and correspond to the technical details. Before
the first use, remove all elements and clean them along
with the entire device.
3.3. DEVICE USE
Operation
1.
Fill the tanks with oil so that level is between the
marks of minimum and maximum level.
2.
Set the thermostat to „0" and insert the plug into an
electricity socket.
3.
Switch on the device by setting the On / Off switch
to the „On" position, the power supply indicator
light will light up. Set the preferred temperature
by turning the thermostat knob, the thermostat
operating indicator light will light up. The device
works in continuous mode. The RCTF 13EH and
RCTF 13DH models, in addition to the continuous
operation described above, have the option of
limiting the working time by means of a timer.
For this purpose, after switching on the device, in
addition to the temperature, it is also necessary
set the time by turning the timer knob. The device
will switch off automatically after the set time has
elapsed (in order to restart the heating of the fryer,
it is necessary to switch the On / Off switch to the
„Off" position, and then to reset the thermostat to
the „0" position
Rev. 17.10.2018
Publicidad
Tabla de contenido
