axalto MagIC X1000 DECT Guia De Instalacion página 5

Introduction
You have chosen an Axalto point of sales terminal. In order to use
your terminal efficiently and in the best conditions, it is
recommended you to carefully read this manual.
Important note: Axalto is not responsible for damage due to
installation or use that are not in accordance with the instructions
given in this manual.
MagIC X1000 DECT Presentation
§ Your MagIC X1000 DECT is a portable point of sales terminal
able to read both Magnetic Stripe Cards and Smart Cards.
§ The MagIC X1000 DECT consists of a hand-held unit and a
docking station. The link between the hand-held unit and the
docking station is provided by a radio-link for data transmission
and 2 electrical contacts to recharge the battery.
§ The hand-held unit houses a printer, a keyboard, a display, a
magnetic card reader, a smart card reader and SAM readers.
§ A docking station provides the connection to phone line and
delivers the power to recharge the battery when the handheld is
placed on it.
Safety recommendations prior to connections
§ Only use the power supply provided with the terminal.
Note: Connecting the terminal to any other external voltage
source is strongly not recommended.
To prevent risk of electric shock:
§ do not open the front or back of the terminal,
§ do not expose the terminal to rain or moisture,
§ call a qualified technician for servicing (the terminal does
not contain any user serviceable part).
§ This terminal is not equipped with an On/Off switch: if you do
not use the terminal and if the terminal is not powered, it will
switch off after a few minutes.
§ If the terminal is dropped accidentally, disconnect the terminal
and call the maintenance centre for assistance.
Lithium battery
The lithium cell sustains the internal memory when the main
power supply is disconnected from the terminal.
This battery has to be replaced only by an authorized
maintenance operator. Replacing the battery may be
dangerous.
The non-respect of this rule would invalidate the warranty.
Dispose of batteries according to the environmental
protection rules and the legislation in effect in your
country.
Installing the SIM sized SAM cards
Notes: Do not use tools for installing SAM cards.
The SIM connectors must be filled following a specific order: use
first the connector on the right. If several cards are needed, insert
the second one in the way to left.
1 - Remove the battery cover at the back of the hand-held unit.
2 - Unlock the SIM sized connector.
3 - Open and insert the SAM card in the connector
4 - Close and lock the connector.
Axalto – 2005
MagIC X1000 DECT
Optional second smart card reader installation
1 - Open and remove the battery cover at the back of the hand-
held unit.
2 - Remove the battery without disconnecting it.
3 - Put in place the Second smart card reader
4 - Bend toward you the connecting cable by holding it by its end.
5 - Drive the connecting cable delicately and all the way in inside
the connector.
6 - Put in place the battery, and close gently the battery cover of
the card reader.
Recommendations on the battery
§ Use only batteries approved by the manufacturer.
§ Use the battery only for its intended purpose.
§ When using the terminal for the first time, the battery should be
fully charged before operating the terminal functions.
§ Note that battery will hold a better charge after the first 3-5
cycles. Be aware batteries las t longer if treated well.
§ Due to unavoidable "self discharge", it is a good idea to charge
the battery before you expect to use them.
§ Never use any battery that is damaged or worn out.
§ Never disassemble or short-circuit a battery.
§ To guaranty the battery lifetime, do not expose terminal to fire,
rain or excessive operating temperature, humidity.
§ Never throw batteries in fire or water.
§ Avoid mechanical knock.
§ Batteries must be recycled or disposed of properly
according to the environment protection rules and the
legislation in effect in your country.
§ Never put refund batteries in domestic or general
refuse.
EN
5