Install The Door Control - Craftsman 139.53965SRT Manual Del Propietário

INSTALLATION STEP 7
Install the Door Control
Locate door control within sight of door, at a minimum
height of 5 feet where small children cannot reach,
away from moving parts of door and door hardware.
If installing into drywall, drill 5/32" holes and use the
anchors provided. For pre-wired installations (as in
new home construction), it may be mounted to a
single gang box (Figure 2).
1. Strip 7/16" of insulation from one end of bell wire
and connect to the two screw terminals on back of
door control by color: white wire to 2 and white/red
wire to the 1.
2. Remove white cover by gently prying at slot in top of
the cover with a small flat head screwdriver. Fasten
with 6AB x 1-1/4" self-tapping screws (drywall
installation) or 6-32 x 1" machine screws (into gang
box) as follows:
• Drill and install bottom screw, allowing 1/8" to
protrude above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid
cracking plastic housing. Do not over tighten.
• Insert top tabs and snap on cover.
3. (Standard installation only) Run bell wire up wall
and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Do not
pierce wire with a staple, creating a short or open
circuit. If your access door is near the garage door,
you may run this wire with the Safety Reversing
Sensor wires along the top of the rail. See page 18.
4. Insert all wires through the opening on top of motor
unit above the terminal block on the back panel
(Figure 3).
5. Strip 7116" of insulation from each set of wires.
Insert door control wire into quick-connect terminals
by color: white wire to white, white/red wire to red.
Separate white and white/black wires sufficiently to
connect to the opener quick-connect terminals.
Twist like colored wires together. Insert wires into
quick-connect holes: white to white and white/black
to grey.
NOTE: When connecting multiple door controls to the
opener, twist same color wires together. Insert wires
into quick-connect holes: white to white and red/white
to red.
6. Use tacks or staples to permanently attach
entrapment warning label to wall near door control,
and manual release/safety reverse test label in a
prominent location on inside of garage door.
NOTE: DO NOT connect the power and operate the
opener at this time. The trolley will travel to the full
open position but will not return to the close position
until the sensor beam is connected and properly
aligned.
Outside Keylock Accessory Connections I
To opener quick-connect terminals: white to white;
I
wh te/red to red.
21
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution:
• Be sure power is not connected BEFORE installing door
control.
• Connect ONLYto 24 VOLTlow voltage wires.
To prevent possible SERIOUSINJURYor DEATHfrom a
closing garage door:
• Install door control within sight of garage door, out of
reach of children at a minimum height of 5 feet, and
away from all moving parts of door.
• NEVERpermit children to operate or play with door
control push buttons or remote control transmitters.
• Activate door ONLYwhen it can be seen clearly, is
properly adjusted, and there are no obstructions to
door travel.
• ALWAYSkeep garage door in sight until completely
closed. NEVERpermit anyone to cross path of closing
garage door.
HARDWARE SHOWN ACTUAL SIZE
6"o x IIIi o,ew
Control Console (std installation)
ij Iwll i
Control Console (pre-wired)
Insulated
Staples
UUI/I J
Dr,/Wall Anchors
PREMIUM
CONTROL
CONSOLE
Lighted
Push Bu_on
/
_ Light
i Lock
...... Top
, _ Mounting
Hole
>Terminal
Screws
Bottom
Mounting
.... Hole
BACK VIEW
Figure 1
REMOVE & REPLACE COVER
To Replace, _o Remove,
Insert _-_ Twist
Top Tabs
_" 1_ _YlT_/I
Here
• //
Figure 2
PRE-WlRED
INSTALLATION
24 Volt
2-Conductor
Bell Wire
Figure 3
WIRING TO TERMINAL BLOCK
Strip 7/16" of insulation from each wire. Insert wires through opening on
top of motor unit above terminal block, then into quick-connect terminals.
Door Control To release wire, push in tab
Connections with screwdriver tip
Red White Grey
_=-7/16"--_
Strip wire 7/16"