Install The Door Control - Craftsman 139.53960SRT Manual Del Propietário

INSTALLATION STEP 6
Install the Door Control
Locate door control within sight of door, at a minimum
height of 5 feet where small children cannot reach,
away from moving parts of door and door hardware.
If installing into drywall, drill 5/32" holes and use the
anchors provided. For pre-wired installations (as in
new home construction), it may be mounted to a
single gang box (Figure 2).
1. Strip 1/4" of insulation from one end of bell wire and
connect to the two terminal screws on back of door
control by color: white to 2 and white/red to 1.
2. Door Control Button: Fasten securely with
6ABx1-l/2" screws.
Console Model: Pry off cover along one side with a
screwdriver blade (see Figure 1). Fasten with
6ABx1-1/4" self-tapping screws (standard
installation) or 6-32x1" machine screws (into gang
box) as follows:
• Install bottom screw, allowing 1//8" to protrude
above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid
cracking plastic housing. 13o not overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run bell wire up
wall and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Be careful
not to pierce wire with a staple, creating a short or
open circuit.
4. Connect the bell wire to the terminal screws on the
motor unit panel: white to 2; white/red to 1.
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach
entrapment warning label to wall near door control,
and manual release/safety reverse test label in a
prominent location on inside of garage door.
DO NOT connect power and operate opener at
this time, The trolley will travel to the full open
position but will not return to the close position
until the sensor beam is connected and properly
aligned.
TopreventpossibleSERIOUS INJURY or DEATH from
electrocution:
• Besurepoweris not connectedBEFORE i nstallingdoor
control.
• Connect ONLY to 24 VOLT low voltagewires.
TopreventpossibleSERIOUS INJURYor DEATH from a
closing garage door:
• Installdoor control within sight of garagedoor,out of
reachof childrenat a minimumheightof 5 feet,andaway
from all movingparts of door.
• NEVER permitchildrento operateor playwithdoorc0ntrol
pushbuttonsor remotecontroltransmitters.
• Activate door ONLY whenit canbe seenclearly,is properly
adjusted,andthereareno obstructionsto door travel.
ALWAYS keepgarage door in sight untilcompletely closed.
NEVER permit anyone to crosspathof closinggarage door.
Outside Keylock Accessory Connections
To opener terminal screws: white to 2; white/red to 1
_] I_!ll_illlllliltltl Illliillllil_>
6AB x 1-1/2" Screw
Door Control Button
H; IAI212 Il1111/12,,t iSIcl 'el/VJ_
Control Console (std installation)
I 116 !; I21 I xII ,! ': Ictr le!; II
Control Console (pre-wired)
HARDWARE SHOWN
ACTUAL SIZE
_ nsulated
Staples
Dry Wall Anchors
Figure 1
REMOVE & REPLACE COVER
TO Replace, To Remove,
Insert Top Twist
Tabs First __._._. Here
Figure 2
PRE-WtRED
INSTALLATION
24 Volt
2-Conductor
Bell Wire in
Gang Box
Lighted
Push Button
Bell
Terminal Wire
Screws
(BACK V_EW)
DOOR CONTROL BUTTON
:_F==_===_== Top
_v Mounting
- Hole
. > Terminal
/ _ Sorews
Bottom
Ben Mounting
Wire _ Hole
(BACK VIEW)
PREMIUM CONTROL CONSOLE
Back Panel
of Opener
18