PELI 9490 Manual Del Usuario

Catalog #9490
Peli 9490 User Manual
Light Operation
Prior to light operation, locate the required fuse.
With a slot screwdriver, screw the fuse into the fuse receptacle on the side of the power pack (A).
1. Press power button on keypad once to switch on. The default setting is the preset* high mode
(as indicated by the three symbols at the top of the screen). (B)
Your remaining run time is displayed in the center of the screen and your battery level at the bottom of the screen.
2. Press the bottom left button
3. Press the up or down buttons on the keypad at any time to enter the Intelligent Control (IC) mode. The IC mode allows you to select any run time up to 24hrs.
In this mode, your power level is displayed at the top of the screen instead of the preset 'sun' symbols. You can go back to preset mode at any time by pressing
the bottom left button on the keypad.
4. Press the power button on the keypad to switch off.
The 9490 IC features three preset modes which provide recommended lux levels over a certain distance. Please see table below:
*
Setting Lux @ 1m
3 Suns 4,000
2 Suns 2,180
1 Sun 670
The 9490 features the ability to be used while charging. When the charger is connected to AC power and the product is switched on, the 9490 will automatically
select a light level to allow continuous operation. - automatic mode. (In this mode, the battery level will remain constant. The light will be at a 50% level.
In AC mode the display will show the battery level and power level but the time display will be replaced by
Manual adjustment of the brightness will still be possible. If the brightness is increased, then automatic mode will be exited, a new runtime will be computed
based upon the new operating conditions. The battery level and the display will revert to the normal IC mode, (or preset mode if the bottom left button has been used).
If the brightness is decreased, the unit will remain in continuous mode (and the battery will charge up slowly).
If the charger is removed, the unit will return to normal operation and the run-time display will show the remaining time for the selected setting.
Bluetooth Operation
The 9490 is equipped with Bluetooth capability and you are able to operate it via the Peli RALS (Remote Area Lighting Systems) app.
To download the RALS app, visit the app store and search for Peli RALS Once installed the app icon should appear on your screen.
Please note that this app requires iOS 7.0 or later.
It is compatible with iPhone, iPad and iPod touch only.
The Bluetooth is active by default while the battery is connected to the 9490. Once you open the app your 9490 should appear
under the 'Found' heading as per the following example: (C) 9490 000001 (the last six digits are your unique serial number).
By selecting this serial number the app should connect to the 9490 RALS and the serial number should now appear under the
'Connected' heading in the app screen and the Bluetooth logo on the 9490 screen should turn from white to blue.
(D) You can connect to multiple 9480/9490 units but only operate one at a time.
Once connected, the default setting is always off. To switch on you can either press the 'on/off' toggle on the app screen
or slide the intensity slider towards the right until you reach your desired light intensity. The app works in conjunction with
the keypad screen on your 9490; as you adjust the slider on the app screen, the remaining run time adjusts on the keypad screen.
The app will remain connected until you either close the app or go out of range*, at which point the Bluetooth logo on the
9490 keypad screen will turn from blue to white. You can override the app control by operating the 9490 keypad if desired.
The Bluetooth can be manually deactivated on the 9490 if required. To deactivate it, switch the 9490 on, then press and hold the bottom left button on the keypad until the
Bluetooth logo in the bottom left of the screen disappears. It can be reactivated again by pressing and holding the same button again until the logo reappears.
*Range varies depending upon the environment in which the unit is being used.
Flash Mode
1 Press and hold the power button for 3 seconds until flashing begins, then select the required power level.
2. To switch flashing mode off, press the power button again.
Power Pack
The 9490 power pack is removable. This allows for continuous use of the product by replacing it with another
fully charged power pack when required. To remove the power pack simply release the clips and lift via
the handle. (E, F)
Power Pack Level
The power pack is equipped with a power level monitor which remains permanently illuminated to tell the user
how much power the battery contains. The level monitor will glow brightly when the product is switched on and dim when not in use.
While the product is switched on, the number of segments illuminated in the level monitor will gradually reduce over time. The product will switch off soon after a single red
flashing segment is displayed. Once the product has switched itself off, the single red segment in the level monitor will continue to flash, indicating that a recharge is required.
Power Pack Charging
The power pack can be charged inside or outside of the main 9490 housing.
1. Remove the dust cap from the charging socket and plug in charger.
2. Connect the charger to the mains AC power supply.
Charge Cycle Indication:
During charging, the level monitor display will become brighter and continue to cycle until all segments of the display are shown. Once the display stops cycling and shows
all segments, the battery is fully charged.
Note: The power pack can be left attached to the charger without any harm to the battery.
Mast Operation
1. Lift the light and pole to a selected position, then twist the red locking collar clockwise to lock the pole in place.
2. To extend the mast, release the clamp on each section and raise. Lock each clamp until you have reached
your chosen height.
3. To collapse the mast, reverse the procedure.
on the keypad to change between high, medium and low power. Your remaining run time varies between these settings.
Lux @ 2m
1,260
700
210
u
Lux @ 3m
620
340
100
--:--
and the hourglass icon will be extinguished.
C
D
E
EN
A B
F