Publicidad
Idiomas disponibles
Idiomas disponibles
STORING STATION PRESETS
For convenience, store up to 3 preset FM stations on the TUNEIT.
This feature allows you to recall known stations that give the best
performance.
1. Tune to a desired station by using the SCAN UP/DN buttons.
2. When a desired FM frequency is shown on the display, press
the SET button on the right side of the TUNEIT once (Figure 3).
3. Choose the desired memory station that you prefer by
pressing the MEM button on the right side of the TUNEIT once
(Figure 4). The order is: CH1 - CH2 - CH3 - CH1 again.
4. Once you have selected the desired memory channel number,
press the SET button (page 1, Figure 1, #6). The desired
frequency will be stored to that memory channel number
(Figure 5).
5. Tune the next frequency that you wish to store by repealing
steps 1-4. Keep in mind that the TUNEIT only stores 3 pre-set
FM stations.
NOTE: To change preset stations please repeat steps 1-4 as
described above.
RECALLING PRESET STATIONS
1. Press the MEM button (page 1, Figure 1, #5) on the right
hand side to select the desired preset station.
2. The first preset channel will be shown on the display to show which station being selected.
3. Press the MEM button (page 1, Figure 1, #5) to scroll through the FM preset stations.
NOTE: To change preset stations, refer back to 'STORING PRESET STATIONS'. Repeat steps 1-4.
RECHARGING FUNCTION
1.
The TUNEIT has a built-in 12 watt (2.4A)
USB port that can recharge your device
at the fastest rate possible.
Simply connect the TUNEIT to your mobile
2.
device with a USB 2 .0 socket cable•, and
your mobile device begins charging. Once
connected, the display on the TUNEIT
shows a blinking Battery symbol- (Figure 6).
3. When the TUNEIT disconnects from your mobile device, the Battery symbol turns off.
NOTE:
A USB cable is not provided. Users need to use their own cables for charging.
Power level doesn't show on the TUNEIT display. Users must check power level on
their device. Some mobile devices with recharge circuit protection may also
deactivate the TUNEIT's Battery symbol, which cannot be shown during charging.
Users need to check their device for charging status.
- Increase the volume level on your portable device
- Check your car audio radio volume
NO SOUND
- Make sure the AUX-IN is fitted properly to your device
- Make sure the selected channel frequency is properly matched to the stereo
- Double check to see that the FM transmitter is properly plugged
NO POWER
into the 12v socket or cigarette lighter
- Make sure the power switch on the portable device is switched on.
NO SIGNAL
- Make sure the FM transmitter power is on, and the car stereo is tuned to
the same channel frequency as the
The user manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided
only in a fom, other than paper, such as on a computer disk or over the internet, the infom,ation required by this section may be included in the
manual in that alternative fom,, provided the user can reasonably be expected to have the capability to access information in that fom,_
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications not exprBSsly
approved by the party rBSponsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the �mits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
�mits are designed to provide reasonable protection against ham,ful interference in a residential instanation. This equipment generates uses
and can radiate radio frequency energy and, if not instaned and used in accordance with the instructions, may cause ham,ful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement: The product complies with the FCC/IC RF Exposure for Low Power Consumer Wireless Power Transfer. RF
exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure
that compliance was demonstrated at 10cm and greater separation from the user body or set the device to lower output power if such function
is available. FCC ID: IKQFMTD3PRO
This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
The tern, "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications
meets the applicable Industry Canada technical specifications. IC: 6955A-FMTD3PRO
OPERATION
TROUBLESHOOTING
transmitter
FM
INFORMATION TO USER
FCC STATEMENT
IC STATEMENT
2
FIGURE3
FIGURE4
FIGURE 5
FIGURE 6
Connect
to mobile
devices for
charging
Blinking
battery
symbol
were
met. This product
Publicidad
