Electrical Safety - Stanley SBR20D1K Manual De Instrucciones

ENGLISH
Position of Date Code (Fig. C)
The Date Code (19), which also includes the year of
manufacture, is printed into the housing.
Example:
2018 XX 58
Year of manufacturing
ADDITIONAL SAFETY INSTRUCTIONS FOR
BATTERIES AND CHARGERS
Batteries
♦ Never attempt to open for any reason.
♦ Do not expose the battery to water.
♦ Do not store in locations where the temperature may
exceed 40 °C.
♦ Charge only at ambient temperatures between 10 °C and
40 °C.
♦ Charge only using the charger provided with the tool.
♦ When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
Chargers
♦ Use your Stanley charger only to charge the battery in the
tool with which it was supplied. Other batteries could burst,
causing personal injury and damage.
♦ Never attempt to charge non-rechargeable batteries.
♦ Have defective cords replaced immediately.
♦ Do not expose the charger to water.
♦ Do not open the charger.
♦ Do not probe the charger.
The charger is intended for indoor use only.
Read the instruction manual before use.

ELECTRICAL SAFETY

Your tool is double insulated; therefore no earth wire is
Your charger is double insulated; therefore no earth wire
is required. Always check that the mains voltage
corresponds to the voltage on the rating plate. Never attempt to
replace the charger unit with a regular mains plug.
♦ If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Service Centre in
order to avoid a hazard.
THE PACKAGE CONTAINS
1 Instruction Manual
1 BL Hammer
2 2Ah Lithium Battery (D2)
1 2Ah Lithium Battery (D1)
1 1A Charger
1 Side Handle
18
SBR20D1K_SBR20D2K_N854635_Rotary Hammer_Manual_VD.indd 18
1 Depth Stop
1 Warranty Card
1 Service Center List
1 Kitbox
♦ Check for damage to the tool, parts or accessories which
may have occurred during transport.
♦ Take the time to thoroughly read and understand this
manual prior operation.
FEATURES (FIG.C)
This tool includes some or all of the following features.
1. On/Off switch
2. Forward/reverse selector
3. Mode selector
4. Depth stop
5. Tool holder
6. Side handle
7. Battery
20. LED work light
21. Battery fuel gauge
ASSEMBLY
WARNING! Before assembly, make sure that the tool
is switched off and unplugged.
USE
WARNING! Let the tool work at its own pace. Do not
overload.
Charging the battery (Fig. A)
The battery needs to be charged before first use and whenever
it fails to produce sufficient power on jobs that were easily done
before. The battery may become warm while charging; this is
normal and does not indicate a problem.
WARNING! Do not charge the battery at ambient
temperatures below 10 °C or above 40 °C.
Recommended charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger will
begin to charge automatically when the cell temperature warms
up or cools down.
♦ To charge the battery, insert the Battery (7) into the charger
(9). The battery will only fit into the charger one way.
♦ Plug the charger (9) into a suitable power source and
switch on.
♦ Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Fitting and removing the battery (Fig. B)
♦ To fit the battery, line it up with the receptacle on the tool
(11). Slide the battery into the receptacle and push until the
battery snaps into place.
♦ To remove the battery, push the release button (12) and
remove the battery from the receptacle.
2020/5/12 4:48 PM