Hammer Drilling - Stanley SBR20D1K Manual De Instrucciones

Fitting the side handle (Fig. C)
♦ Turn the grip counterclockwise until you can slide the side
handle (6) onto the front of the tool as shown.
♦ Rotate the side handle into the desired position.
♦ Tighten the side handle by turning the grip clockwise.
Fitting and setting the depth stop (Fig. C)
♦ Depress the button (8).
♦ Insert the depth stop (4) into the mounting hole as shown.
♦ Set the depth stop (4) to the desired position. The maximum
drilling depth is equal to the distance between the tip of the
drill bit and the front end of the depth stop.
♦ Release the button (8).
Fitting an accessory (Fig. D - E)
♦ Clean and grease the shank (13) of the accessory.
♦ Pull back the sleeve (14) and insert the shank into the tool
holder (5).
♦ Push the accessory down and turn it slightly until it fits
into the slots.
♦ Pull on the accessory to check if it is properly locked. The
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
♦ To remove the accessory, pull back the sleeve (14) and
pull out the accessory.
Keyed chuck (Fig. F)(Optional)
♦ Open the chuck by turning the sleeve (15) anti-clockwise.
♦ Insert the bit shaft (17) into the chuck.
♦ Insert the chuck key (18) (Optional) into each hole (16) in
the side of the chuck and turn clockwise until tight.
WARNING! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
WARNING! Do not apply chisels when the tool is in the
drilling mode.
Switching on and off (Fig. G)
♦ To switch the tool on, press the on/off switch (1).
♦ To switch the tool off, release the on/off switch.
Forward/reverse action (Fig. H)
♦ Move the selector (2) to indicate the direction you require.
Selecting the operating mode (Fig. I)
The tool can be used in three operating modes.
♦ To operate the operating mode selector (3), push the unlock
button (22) and rotate the selector towards the required
position, as indicated by the symbols.
Drilling
♦ For drilling in steel, wood and plastics, and for screwdriving
set the operating mode selector (3) to the position (I1).

Hammer drilling

♦ For hammer drilling in masonry and concrete, set the
operating mode selector (3) to the
hammering, the tool should not bounce and run smoothly.
If necessary, increase the speed.
SBR20D1K_SBR20D2K_N854635_Rotary Hammer_Manual_VD.indd 19
Chiseling
♦ For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (3) to the
position (I3).
♦ When changing from hammer drilling to chiselling, turn the
chisel to the desired position. If resistance is felt during
mode change, slightly turn the chisel to engage the spindle
lock.
LED Work Light
When the tool is activated by pulling the trigger switch (1), the
integrated LED work light (20) will automatically illuminate the
work area. NOTE: The work light is for lighting the immediate
work surface and is not intended to be used as a flashlight.
Battery Fuel Gauge (fig.J)
The tool is equipped with a battery fuel gauge (21).This can
be used to display the current level of charge in the battery
during use. It does not indicate tool functionality and is subject
to variation based on product components, temperature and
end-user application.
Checking battery charge during use:
♦ Press the battery fuel gauge button (J1).
♦ The three LEDs (J2) will illuminate indicating the percent
of charge in the battery (Fig. J).
♦ If LED light does not lluminate, charge battery.
Note: This battery is designed to not operate when a charge
below 20% of its capacity is reached. After the battery charge
is depleated, the tool will not operate until after the battery has
been recharged.
MAINTENANCE
Your Stanley corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. To ensure satisfactory operations, the tool
must be maintained and cleaned regularly
installing and removing accessories, before adjusting or
changing set-ups or when making repairs. Be sure the
trigger switch is in the OFF position. An accidental start-up can
cause injury.
♦ This machine is not user-serviceable. If problems occur
contact an authorised repair agent.
♦ The tool will automatically switch off when the carbon
brushes are worn.
♦ Switch off and unplug the appliance/tool.
♦ Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
♦ Or run the battery down completely if it is integral and then
position (I2). When
switch off.
WARNING! Do not use this tool to mix or pump easily
combustible or explosive fluids (benzine, alcohol, etc.).
Do not mix or stir inflammable liquids labelled
accordingly.
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
WARNING! Before performing any maintenance on
corded/ cordless power tools:
ENGLISH
19
2020/5/12 4:48 PM