Safety Of Others - Black and Decker RS890 Manual De Instrucciones

ENGLISH
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
@
Warning! Additional safety warnings for jigsaws
and reciprocating saws
Hold power tool by insulated gripping surfaces when
u
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator
an electric shock
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
@
Warning! Contact with or inhalation of dusts
arising from cutting applications may endanger
the health of the operator and possible bystand-
ers. Wear a dust mask specifically designed for
protection against dust and fumes and ensure
that persons within or entering the work area are
also protected.
Keep hands away from cutting area. Never reach
u
underneath the work piece for any reason. Do not insert
fingers or thumb into the vicinity of the reciprocating blade
and blade clamp. Do not stabilise the saw by gripping the
shoe.
Keep blades sharp. Dull or damaged blades may cause
u
the saw to swerve or stall under pressure. Always use the
appropriate type of saw blade for the workpiece material
and type of cut.
When cutting pipe or conduit, make sure that they are free
u
from water, electrical wiring, etc.
4
(Original instructions)
Do not touch the workpiece or the blade immediately after
u
operating the tool. They can become very hot.
Be aware of hidden hazards, before cutting into walls,
t
floors or ceilings, check for the location of wiring and
pipes.
The blade will continue to move after releasing the
t
switch. Always switch the tool off and wait for the saw
blade to come to a complete standstill before putting
the tool down.
The intended use is described in this instruction manual.
u
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Do not eat, drink or smoke in the work area.
u
Pruning
Before attempting to prune a tree, ensure there are not by-
laws or regulations that would prohibit or control the felling of
the tree.
Be aware of the direction a branch may fall. Consider all
u
conditions that may affect the direction of fall, including:
the length and weight of the branch to be cut
t
the intended direction of fall
t
any unusual heavy limb structure or decay
t
the presence of surrounding trees and obstacles,
t
including overhead lines
t
the intertwinement with other branches
t
the speed and direction of the wind.
t
Consider access to the tree limb.
u
Tree branches are liable to swing towards the tree trunk. In
addition to the user, any bystander, building or object below
the branch is at risk of being struck by the branch.

Safety of others

This appliance is not intended for use by persons (includ-
u
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
u
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u