Ice Maker And Storage Bin - JENN-AIR JFFCC72EFP Manual De Uso

The Ice Dispenser
IMPORTANT:
If the ice cubes are hollow or have an irregular shape, it could
■
be because of low water pressure. See the "Water Supply
Requirements" section.
Ice travels from the ice storage bin through the dispenser
■
chute to the dispenser. To turn off the ice maker, see the
"Ice Maker and Storage Bin" section.
The dispenser may continue to make noise and ice may
■
continue to dispense for several seconds after releasing
the dispenser button or paddle.
To Clean the Ice Dispenser Chute:
Humidity causes ice to naturally clump together. Ice particles can
build up until the ice dispenser chute becomes blocked.
If ice is not dispensed regularly, it may be necessary to empty the
ice storage bin and clean the ice delivery chute, the ice storage
bin, and the area beneath the storage bin every 2 weeks.
If necessary, remove the ice clogging the storage bin and
■
delivery chute using a plastic utensil.
Clean the ice delivery chute and the bottom of the ice storage
■
bin using a warm, damp cloth, and then dry thoroughly.
To Dispense Ice - Paddle Dispensing
1. Select the desired type of ice by pressing CUBED ICE or
CRUSHED ICE.
WARNING
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
2. Press a sturdy glass against the dispenser paddle. Hold the
glass close to the dispenser opening, so ice does not fall
outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to
the paddle to activate the ice dispenser. Pressing hard will not
make the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing.
NOTE: Ice may continue to dispense for several seconds after
removing the glass from the dispenser paddle. The dispenser may
continue to make noise for a few seconds after dispensing.
Cut Hazard
The Dispenser Drip Tray
!
Replace
Filter
Order Filter Door
! ! Ajar
!
The drip tray can be removed to carry to the sink to empty
or clean.
Lift up on the front edge of the tray and pull forward to remove.
■
The drip tray can also slide out to assist in Measured/
■
Favorite Fill.
The Dispenser Light
1. When you use the dispenser, the light will automatically
turn on.
2. The dispenser light also serves as an automatic night light.
Once the ambient light in the room is reduced, the auto
sensor will cause the dispenser light to illuminate.
The Dispenser Lock
The dispenser can be locked for easy cleaning or to avoid
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the refrigerator
or the dispenser light. It simply deactivates the controls and
dispenser levers. To turn off the ice maker, see the "Ice Maker
and Storage Bin" section.
Touch and hold CUBED ICE for 3 seconds to lock the
■
dispenser.
Touch and hold CUBED ICE for 3 seconds to unlock the
■
dispenser.
The display screen indicates when the dispenser is locked.
■

Ice Maker and Storage Bin

IMPORTANT: To avoid low ice production and poor quality ice,
flush the water system before turning on the ice maker. See the
"Water Dispenser" section.
Following installation, allow 24 hours to produce the first
■
batch of ice. Discard the first 3 batches of ice produced.
Allow 2 to 3 days to fill the ice storage bin.
The quality of your ice will be only as good as the quality of
■
the water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener is operating properly and is
well-maintained.
If the ice in the storage bin clumps together, break up ice
■
using a plastic utensil and discard. Do not use anything sharp
to break up the ice. This can cause damage to the ice bin
and the dispenser mechanism.
Do not store anything in the ice storage bin.
■
a1 oz = b1 L
"#$#! a2 oz = b2 L !
Calibration
a3 oz = b3 L
! !
!
Dispense
!
!
%&#'#(')!"#$# !
!
27