Ingersoll Rand 2X MULTI-VANE Serie Especificaciones Del Producto página 3

Product Safety Information
Intended Use:
Close Quarter Multi–Vane® Drills, Nonreversible Models 2XJA1–EU, 2XKA1–EU and 2XMA2 -EU, and Reversible Models 22JA1–EU, 22KA1–EU,
22MA2–EU and 22NA1–EU, are designed forheavy steel fabrication and maintenance.
For additional information refer to Air Drills Product Safety Information Manual Form 04580353.
Manuals can be downloaded from www.ingersollrandproducts.com
Product Specifi cations
Free
Speed
Models
rpm
2XJA1–EU 1025
2XKA1–EU 725
22JA1 1025
22JA1–EU 1025
22KA1 725
22KA1–EU 725
22MA2 350
22MA2–EU 350
22NA1 280
22NA1–EU 280
22KWA1 725
22KWA1–EU 725
22N51–EU 280
Models
2XJA1–EU
2XKA1–EU
22JA1
22JA1–EU
22KA1
22KA1–EU
22MA2
22MA2–EU
22NA1
22NA1–EU
22KWA1
22KWA1–EU
22N51–EU
Governor Adjustment
When installing a new Governor Assembly, screw the Adjusting Nut onto the Stem to dimension "A" shown in Dwg. TPD497. This will usually
result in the proper governed free speed of the Spindle. However, this is only an approximate setting and, after checking with a tachometer,
further adjustment may be necessary. Screw the Nut farther onto the Stem to increase the speed; back it off to decrease the speed.
A=1–31/32" for Drills with Standard Throttle
A = 1–7/8" for Motors equipped with Remote Control
The correct governed free speed for the
various Models at the Spindle is:
Model
22JA1–EU, 2XJA1–EU
22KA1–EU, 22KWA1–EU, 2XKA1–EU
22MA2–EU, 2XMA2–EU
22NA1–EU
03523024_ed23
Capacity in Steel
Drilling Reaming
in. mm in.
Nonreversible Roll Throttle
9/16 14 3/8
9/16 14 7/16
Reversible Roll Throttle
9/16 14 3/8
9/16 14 3/8
9/16 14 7/16
9/16 14 7/16
7/8 22 5/8
7/8 22 5/8
7/8 22 5/8
7/8 22 5/8
--- --- ---
--- --- ---
--- --- ---
Pressure
---
96.4
---
---
---
96.4
---
94.1
---
---
---
96.4
Speed, rpm
1025
725
350
280
mm
10 0.703–16 thread, 0–1/2" Chuck
11 0.703–16 thread,0–1/2" Chuck
10 Stub Taper, Threaded, 0–1/2" Chuck
10 Stub Taper, Threaded, 0–1/2" Chuck
11 Stub Taper, Threaded, 0–1/2" Chuck
11 Stub Taper, Threaded,0–1/2" Chuck
16
16
16 Stub Taper, Threaded 5/8" Square Drive
16 Stub Taper, Threaded,5/8" Square Drive
--- Stub Taper, Threaded,1/2" Shank Wood, Bit Chuck
--- Stub Taper, Threaded,1/2" Shank Wood, Bit Chuck
Reversible
---
Sound Level dB(A)
ANSI S5.1–1971
Power (ISO3744)
(Dwg. TPD497)
Spindle,
Attachment
No. 2 Morse Taper Socket
No. 2 Morse Taper Socket
Vibration (m/s2)
---
109.4
---
---
---
109.4
---
107.1
---
---
---
109.4
A
EN
(ISO28927)
Level
< 2.5
< 2.5
< 2.5
< 2.5
< 2.5
< 2.5
< 2.5
< 2.5
< 2.5
< 2.5
< 2.5
< 2.5
< 2.5
EN-1