Machine Assembly - Alpina T 1.0 EJ 223536 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 48
6
EN
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust col-
lection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be con-
trolled with the switch is dangerous and must be re-
paired.
c) Disconnect the plug from the power source before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety meas-
ures reduce the risk of starting the power tool acci-
dentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.

4. MACHINE ASSEMBLY

WARNING!
very carefully so as not to impair the safety
and efficiency of the machine. If in doubt, con-
tact your dealer.
WARNING!
not plugged into the mains socket.
WARNING!
ing the assembly should be done on a flat and
stable surface, with enough space for moving
the machine and its packaging, always making
use of suitable equipment.
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.
1. MOUNTING THE FRONT HANDGRIP
(Fig. 1)
– Fit the lower part (3) with guard on the drive tube
– Fit the front handgrip (4) by using the screws (5).
Mount the components
Make sure the machine is
Unpacking and complet-
SAFETY WARNINGS / MACHINE ASSEMBLY
e) Maintain power tools. Check for misalignment or
obstruction of moving parts, breakage of parts
and any other condition that may affect the power
tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to become jammed and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Using the power tool for operations
other than those intended could result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a qualified re-
pair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
– Before tightening the screws (4), align the hand-
grip correctly with respect to the drive tube.
– Fully tighten the screws (4).
2. MOUNTING THE ROD (Fig. 2)
– Push the lower part of the rod (1) right down un-
til the stop pin (2) clicks into the hole (3) in the
rod. This is easier to do if you rotate the lower
part of the rod (1) slightly in both directions; in-
sertion is completed when the stop pin (2) pro-
trudes completely from the hole (3).
– Once inserted, tighten the knob (4) securely.
3. MOUNTING THE GUARD (Fig. 3)
WARNING!
correctly to respect the safety requirements
and the correct position of the line cutting
knife.
– Assemble the guard (1) using the four screws (2)
to fasten it.
IMPORTANT
can never be removed.
The guard must be fitted
Once mounted, the guard

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Sgt 1000 j

Tabla de contenido