Maintenance And Service; Maintenance And Cleaning - Bosch GSS 230 AVE Manual Original

Ocultar thumbs Ver también para GSS 230 AVE:
Tabla de contenido

Publicidad

OBJ_BUCH-1665-001.book Page 15 Monday, July 9, 2012 11:08 AM
For the working of paint/enam-
el coats or primers and fillers
For sanding off paint
For sanding primer
For final sanding of primers
before coating
Note: To avoid tearing of the sanding sheet, use only sanding
sheets with a grain size of 80 or less.
Replacing the Sanding Plate (see figure F)
The sanding plate 10 can be replaced, if required.
Unscrew the 6 screws 16 completely and remove the sanding
plate 10. Attach the new sanding plate 10 and tighten the
screws again.
Specialty Sanding Plates
You can replace the supplied sanding plate 10 with a specialty
sanding plate, which is available as an accessory.
The specialty sanding plate is attached in the same manner as
the one supplied.
Attach and remove the respective sanding sheets in the same
manner as when changing original sanding sheets.
Extended Sanding Plate, Rectangular, Thin (see figure G)
Use of the rectangular, thin, extended sanding plate 17 ena-
bles sanding at hard-to-reach locations and narrow interspac-
es, e. g. on window and door sills, grooves or behind radiators
or water pipes.
To mount the rectangular, thin, extended sanding plate 17,
use the corresponding screws 19.
Extended Sanding Plate, Triangular (see figure H)
Use of the extended triangular sanding plate 21 enables sand-
ing in edges and corners.
Finish-sanding Plate (without velcro backing)
(see figures A and B)
When operating mainly with standard sanding sheets without
velcro backing, it is recommended to use the finish-sanding
plate without velcro backing. Due to its plane sanding plate
surface, optimum results are achieved, especially for finish
sanding.
Auxiliary Handle
The auxiliary handle 1 enables convenient handling and opti-
mal distribution of power, especially at high removal rates.
Fasten the auxiliary handle 1 with screw 2 to the casing.
Operation
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Bosch Power Tools
Switching On and Off
Grain size
To start the machine, press the On/Off switch 4 and keep it
40–320
pressed.
To lock the pressed On/Off switch 4, press the lock-on button
5.
To switch off the machine, release the On/Off switch 4 or
coarse
40, 60
when it is locked with the lock-on button 5, briefly press the
medium 80, 100, 120
On/Off switch 4 and then release it.
fine
180, 240, 320
When not using the power tool, switch it off in order to save
energy.
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the orbital stroke
rate 3, you can preselect the required orbital stroke rate, even
during operation.
The required stroke rate depends on the material and the
working conditions and can be determined through practical
testing.
Working Advice
Wait until the machine has come to a standstill before
placing it down.
When sanding, the removal capacity is mainly determined by
the sanding sheet selection as well as through the preselected
orbital stroke rate.
Only flawless sanding sheets achieve good sanding capacity
and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this increas-
es the working life of the sanding sheets.
Intensifiying the sanding pressure does not lead to an in-
crease of the sanding capacity, but to increased wear of the
machine and the sanding sheet.
A sanding sheet that has been used for metal should not be
used for other materials.
Use only original Bosch sanding accessories.

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
English | 15
2 609 932 841 | (9.7.12)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Gss 280 ave

Tabla de contenido