Fiap Digiswim Active Manual De Instrucciones página 4

FIAP DigiSwim Active
GB
1. Features

For pool and pond

Water temperature wireless (433 MHz), range max. 30 m (free field), with tendency indicator

Stainless steel probe with 100 mm measuring depth
 Indoor temperature

Adjustable temperature alarm for all channels

Maximum and minimum values

Clock with alarm and date

Expandable up to 3 outdoor transmitters, also for the control of outdoor temperature and remote
rooms, e.g. children's room, wine-cellar

Very simple installation, no cables required
2. Elements
2.1 Receiver (Display unit)
LCD
A1: Channel number
A2: Water temperature
A3: Time
A4: Battery indicator transmitter
A5: Trend indicator water temperature
A6: Indoor temperature
Buttons
B1: "▲ (12/24)" button
B2: „SET/MODE" button
B3: "SEARCH/CHANNEL" button
B4: "▼ ALARM ON/OFF" button
B5: "ALERT" button
B6: "MAXIMIN" button
B7: "RESET" button
Housing
C1: Wall Mount Hole
C2: Battery Compartment
C3: Stand (removable)
2.2 Pool Sensor (transmitter)
D1: "TX" button
D2: "°C/°F" button
D3: Transmission indication LED
D4: Water temperature
D5: Water temperature sensor
D6: For fastening rope
D7: Screws battery compartment
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
7
www.fiap.com
FIAP DigiSwim Active
3. Getting started
3.1 Insert battery

Place both instruments on a desk with a distance of approximately 1.5 meter. Check that no other
electronic devices are close.

Press and hold "TX" button and "°C/°F" button at the same time for 3 seconds to switch on the
transmitter. The current temperature and channel 1 are shown on the LCD.

Insert the attached batteries (3 x 1.5 V AA) into the battery compartment of the display unit,
observing the correct polarity.
3.2 Reception of temperature transmitter
The display unit automatically starts scanning the 433 MHz signal to register the thermo sensor unit after
batteries are inserted. If the reception of outdoor values fails, "- -" appears on the display. Check the batteries
and try it again. Check if there is any source of interference.
Manual initialization can be helpful. Hold "CHANNEL" button on the display unit for 3 seconds. The registered
transmitter (channel) is cancelled.
Press "TX" button on the transmitter. The display unit gives a "beep" sound if it received the temperature.
4. How to operate

Important: Buttons with not function while scanning the outdoor temperature signal.

During operation, all successful settings will be confirmed by an acoustical signal.

The instrument will quit the setting mode, if there is no button used within 5 seconds period.

Holding „▲" or „▼" buttons, you will enter fast mode.
4.1 Setting of clock and calendar

Hold "MODE" button for 3 seconds. The hour digit is flashing. Press „▲" or „▼" buttons to adjust
hours. Using "MODE" button you can switch to setting minutes, seconds, year, month/day sequence,
month, day, time zone and day-of-week language.

In "month/day sequence" the two different date displays can be selected: Month/date (American
version) or date/month (European version).

Day-of-week language: English (EN), German (GE), French (FR), Spanish (ES), Italian (IT), Dutch
(NE), Danish (DA).

Choose 12 HR or 24 HR system by pressing the „▲ (12/24)" button.
4.1.1 Indication of date

Press "MODE" button to show the date.
4.2 Alarm clock function

Select your desired alarm by pressing "MODE" button again:
Alarm 1
Alarm 2

Set the alarm time in the desired alarm mode. Hold "MODE" button for 3 seconds. The hour digits are
flashing. Press „▲" or „▼" button to adjust the time. Confirm with "MODE" button. Set minutes in the
same way.

To activate or deactivate the alarm function press „▼ AL ON/OFF" in the respective alarm mode.
"ON" or "OFF" appears on the display.

Once the alarm starts to ring, you can stop the alarm by pressing any button.
4.3 Thermometer
4.3.1 Change °C/°F

Press "▼ ALARM ON/OFF" button to select temperature display in Celsius mode or Fahrenheit
mode.
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
8
www.fiap.com