Additional Safety Warnings - Silver Eagle SE116 Manual De Instrucciones

To reduce the risk of injury, anyone using, repairing, maintaining, or changing accessories on this tool must read and understand these
instructions before performing any of these tasks.
Always inspect, operate, and maintain this tool in accordance
with American National Standards Institute Safety Code of
Portable Air Tools (ANSI B186.1) and any other applicable safety
codes and regulations.
These tools are rated at 90-115 psi / 6.2-8 bar max air pressure
for safety, top performance, and maximum durability of parts; do
not exceed this pressure while the tool is running.
Always shut off air supply, drain hose of air pressure and
disconnect tool from air supply when not in use, before
changing accessories, or when making repairs.
Never direct air at yourself or anyone else.
Always wear impact-resistant eye and face protection when
operating or performing maintenance on this tool.
High sound levels can cause permanent hearing loss. Always
use hearing protection when using this tool as recommended by
your employer or OSHA regulation.
Do not wear jewelry or loose fitting clothes.
Do not use quick disconnect couplings at tool. See operating
instructions for proper set up.
Whipping hoses can cause serious injury. Always carefully check
for damaged or loose hoses and fittings before operating this
tool.
Avoid direct contact with accessories during and after use.
Gloves should be worn to reduce the risk of cuts or burns.
Use only sockets and accessories rated for use with Impact
Wrenches which are in good condition. Sockets in poor condition
or hand sockets and accessories can shatter and cause injury.
Never run the tool off of the work. The tool may run too fast and
cause the accessory to be thrown off of the tool.
Serious injury can result from over-torqued or under-torqued
fasteners. Assemblies requiring a specific torque must be
checked using a torque meter.
"Click" torque wrenches do not check for potentially dangerous
over-torque conditions.
Slipping, tripping, and/or falling while operating air tools can
be a major cause of serious injury or death. Be aware of your
surroundings and any excess hose left on the walking or working
surface.
Pneumatic tools can cause vibration in use. Vibration, repetitive
motions or uncomfortable positions over extended periods of
time may be harmful to your hands and arms. Discontinue use
of tool if discomfort, tingling feeling or pain occurs. Consult a
physician before resuming use if any of these symptoms occur.
OPERATION
This product is designed to tighten or loosen threaded fasteners.
No other use is permitted.
This tool is an impacting tool and not a torque meter. When
specific torque is required, it must be checked with a torque
meter after fitting the fastener with the Impact.
SAFETY INSTRUCTIONS - DO NOT DISCARD - GIVE TO USER
SE116
SE116 1" Drive Impact Wrench
WARNING
Do not stretch or overreach while using this tool.
If tool appears to malfunction, remove from service immediately
and arrange for repair.
Never use tool if there is any chance of coming into contact with
line electricity.
Use only Matco certified spare parts for any repair made to tool.
Repairs should only be performed by properly trained persons.
Do not lock, tape or wire the tool valve in the "on/off" position.
Do not allow the exhaust air to come in contact with hot surfaces
or flames.
Avoid inhaling dust or handling debris from the work process,
which can be harmful to your health. Use dust extraction and
wear respiratory protective equipment when working with
materials which produce airborne particles.
Some dust created by power sanding, sawing, grinding, drilling
and other construction activities contains chemicals known to
the State of California to cause cancer and birth defects or other
reproductive harm. Some examples of these chemicals are:
- Lead from lead based paints
- Crystalline silica bricks and cement and other masonry
products
- Arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.

Additional Safety Warnings

Do not modify this tool or its accessories.
This tool is not recommended for use in explosive atmospheres
or underwater use.
Operators and maintenance personnel must be physically able
to handle the bulk, weight, and power of this tool.
This tool is for professional use only.
If a nut does not move within five seconds, use a larger size
Impact. Do not use Impact Wrench beyond rated capacity, as
this can drastically reduce the tool life.
2 4/3/12