Mitsubishi Electric Lossnay LGH-150RVXT-E Instrucciones De Instalación página 19

Function settings (continued)
No.42
Indoor temperature correction
Set the correction for the indoor temperature displayed on the
PZ-61DR-E screen by function
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
- -
- -
N/A - - 42
- -
- -
- -
- -
- -
- -
- -
No.51
Automatic ventilation mode setting
Set the pattern of conditions to go into By-pass mode in automatic
ventilation operation.
When setting Data is set "3" by PZ-61DR-E, function
and No. 54 are available.
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
OFF
(Factory setting)
SW2-7 51
ON
- -
* Pattern A is more likely to become By-pass mode than pattern B.
Note;
The ventilation mode follows the table below.
Interlocked air conditioner
Remote controller
(Mr. Slim or City Multi)
Energy recovery
ventilation mode
Either Yes or No
By-pass ventilation
mode
Cooling/Stop
Automatic
Other than above
Eng-18
No. 37 .
Setting The correction to
check thermistor detection
0 -7 ˚C
1 -6 ˚C
2 -5 ˚C
3 -4 ˚C
4 -3 ˚C
5 -2 ˚C
6 -1 ˚C
7
0 ˚C
(Factory setting)
8 +1 ˚C
9 +2 ˚C
10 +3 ˚C
11 +4 ˚C
12 +5 ˚C
13 +6 ˚C
14 +7 ˚C
No. 52 ,
Setting Conditions to go into
check By-pass mode
0
DIP-SW priority
(Factory setting)
Pattern A
Indoor temperature is 16 ˚C or more
1 Outdoor temperature is 16 ˚C or more
Indoor temperature -
outdoor temperature ≥ 0 ˚C
Pattern B
Indoor temperature is 22 ˚C or more
2 Outdoor temperature is 18 ˚C or more
Indoor temperature -
outdoor temperature ≥ 2 ˚C
3 Free setting
Lossnay
Energy recovery ventilation
mode
By-pass ventilation mode
Automatic (Follows the map)
Always energy recovery
ventilation mode
Automatic ventilation mode setting 1)
No.52
Outdoor and indoor temperature gap
Set one of conditions for By-pass mode in auto ventilation operation,
temperature gap between indoor and outdoor.
This function is N/A from Lossnay unit DIP-SW.
This function is available when setting Data 3 is selected at function
No. 51.
DIP-SW
SW No. Setting
-
-
-
-
N/A
-
-
-
-
Automatic ventilation mode setting 2)
No.53
The lowest outdoor temperature
Set one of conditions for By-pass mode in auto ventilation operation,
minimum outdoor temperature which comes in indoor directly.
This function is N/A from Lossnay unit DIP-SW.
This function is available when setting Data 3 is selected at function
No. 51.
DIP-SW
SW No. Setting
No. 53 ,
-
-
-
-
-
-
-
-
N/A
-
-
-
-
-
-
-
-
PZ-61DR-E
Setting Setting
check check
Function No. Setting Data
0
-
(Factory setting)
- 1
- 2
- 3
52
- 4
- 5
- 6
- 7
PZ-61DR-E
Setting Setting
check check
Function No. Setting Data
- 0
- 1
- 2
- 3
- 4
- 5
6
-
(Factory setting)
- 7
53
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
Indoor temperature -
outdoor temperature
0 ˚C or more
1 ˚C or more
2 ˚C or more
3 ˚C or more
4 ˚C or more
5 ˚C or more
6 ˚C or more
7 ˚C or more
Outdoor temperature
10 ˚C or more
11 ˚C or more
12 ˚C or more
13 ˚C or more
14 ˚C or more
15 ˚C or more
16 ˚C or more
17 ˚C or more
18 ˚C or more
19 ˚C or more
20 ˚C or more
21 ˚C or more
22 ˚C or more
23 ˚C or more
24 ˚C or more
25 ˚C or more