Bosch PCM 8 S Manual Original página 47

Ocultar thumbs Ver también para PCM 8 S:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 68
– Hold the workpiece in this position and slow-
ly guide the tool arm upward again.
– Clamp the workpiece.
– Switch the laser beam on with switch 29.
The laser beam must be in alignment with the
cutting line on the workpiece over the complete
length, also when the tool arm is lowered.
Adjusting: (see figure T3)
– Loosen the knurled screw 60.
– Turn set screw 61 (horizontal laser position-
ing) and/or 62 (vertical laser positioning) un-
til the laser beam is flush with the cutting line
on the workpiece over the complete length.
– Carefully tighten the knurled screw again.
Setting the Standard Bevel Angle 0°
(Vertical)
– Bring the machine into the transport posi-
tion.
– Turn the saw table 17 until it engages at 0°.
Checking: (see figure U1)
– Set an angle gauge to 90° and place it on the
saw table 17.
The leg of the angle gauge must be flush with
the saw blade 8 over the complete length.
Adjusting: (see figure U2)
– Loosen the clamping lever 31.
– Loosen the lock nut of the stop screw 22 us-
ing a commercial box-end or open-end span-
ner (size 10 mm).
– Screw the stop screw in or out until the leg
of the angle gauge is flush with the saw blade
over the complete length.
– Retighten the clamping lever 31 again.
– Afterwards, retighten the lock nut of the stop
screw 22 again.
In case the angle indicator 53 is not in a line with
the 0° mark of the scale 63 after the adjust-
ment, loosen the screw 64 using a commercial
Phillips screwdriver and align the angle indica-
tor along the 0° mark.
Bosch Power Tools
Setting the Standard Bevel Angle 45°
(Vertical)
– Bring the power tool into the working posi-
tion.
– Turn the saw table 17 until it engages at 0°.
– Loosen the clamping lever 31 and tilt the tool
arm leftward to the stop (45°) by the handle
5.
Checking: (see figure V1)
– Set an angle gauge to 45° and place it on the
saw table 17.
The leg of the angle gauge must be flush with
the saw blade 8 over the complete length.
Adjusting: (see figure V2)
– Loosen the lock nut of the stop screw 21 us-
ing a commercial box-end or open-end span-
ner (size 10 mm).
– Screw the stop screw in or out until the leg
of the angle gauge is flush with the saw blade
over the complete length.
– Retighten the clamping lever 31 again.
– Afterwards, retighten the lock nut of the stop
screw 21 again.
In case the angle indicator 53 is not in a line with
the 45° mark of the scale 63, firstly check the 0°
setting for the bevel angle and the angle indica-
tor again. Then repeat the adjustment of the 45°
bevel angle.
Aligning the Fence
– Bring the machine into the transport posi-
tion.
– Turn the saw table 17 until it engages at 0°.
Checking: (see figure W1)
– Set an angle gauge to 90° and place it on the
saw table 17 between the fence 10 and the
saw blade 8.
The leg of the angle gauge must be flush with
the fence over the complete length.
English | 47
1 609 929 U68 | (23/10/09)

Publicidad

Tabla de contenido
loading

Tabla de contenido