Safety Instructions For Maintenance; Assembly - Husqvarna W520 Manual Del Usuario

• Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
• Do not smoke near the fuel or the engine.
• Do not put warm objects near the fuel or the engine.
• Do not add the fuel when the engine is on.
• Make sure that the engine is cool before you refuel.
• Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
• Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
• Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
• Move the product a minimum of 3 m / 10 ft from the
position where you filled the tank before a start.
• Do not fill the fuel tank fully. Heat causes the fuel to
expand. Keep a space at the top of the fuel tank.

Safety instructions for maintenance

WARNING: Read the warning instructions
that follow before you use the product.
Introduction
WARNING: Before you assemble the
product, you must read and understand the
safety chapter.
WARNING: Remove the spark plug cable
from the spark plug before you assemble the
product.
To assemble the handle
1. Loosen the lower knobs on the left and the right side
of the product. Make sure that the plastic washer is
in the recess in the handle bracket. (Fig. 29)
2. Install the handle folded forward as shown in the
illustration. (Fig. 30)
a) Make sure that the plastic washer is between the
handle and the handle bracket.
b) Attach the handle to the handle bracket.
3. Lift the handle up. (Fig. 31)
4. Tighten the knobs fully. To adjust the handle height,
To adjust the handle height on page 12 .
refer to
5. Put the wires in the cable brackets. Make sure that
the wires are not twisted. Attach the cable brackets
to the handle. (Fig. 32)
6. Use a cable tie to attach the cables to the handle
bracket. (Fig. 33)
12
• The exhaust fumes from the engine contain carbon
monoxide, an odourless, poisonous and very
dangerous gas. Do not start the engine indoors or in
closed spaces.
• Before you do the maintenance on the product, stop
the engine and remove the ignition cable from the
spark plug.
• Use protective gloves when you do maintenance on
the cutting equipment. The blade is very sharp and
cuts can easily occur.
• Accessories and changes to the product that are not
approved by the manufacturer, can cause serious
injury or death. Do not change the product. Always
use accessories that are approved by the
manufacturer.
• If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
• Only do the maintenance as given in this owner's
manual. All other servicing must be done by an
approved Husqvarna service agent.
• Let an approved Husqvarna service agent do
servicing on the product regularly.
• Replace damaged, worn or broken parts.

Assembly

To adjust the handle height
1. Loosen the lower knobs.
2. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 34)
3. Set the handle height in 1 of the 2 available
positions.
4. Move the knobs up in the direction of the handlebar
until they stop and you hear a click. (Fig. 35)
5. Tighten the knobs fully.
To set the product in transport position
1. Remove the grass catcher.
2. Loosen the lower knobs.
3. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 34)
4. Fold the handle forward. (Fig. 36)
To set the product in operation position
1. Lift the handlebar up. (Fig. 31)
2. Move the knobs up in the direction of the handlebar
until they stop and you hear a click. (Fig. 35)
3. Tighten the knobs fully.
To assemble the grass catcher
1. Attach the grass catcher frame to the grass bag with
the rigid part of the bag on the bottom. Keep the
handle of the frame on top of the grass bag. (Fig. 37)
1500 - 001 - 02.07.2020