Euro-Cart express Manual De Instrucciones página 9

OPERATION MANUAL
UNFOLDING THE STROLLER
In order to unfold the stroller, release the automatic lock
(fig. 1), and pull the stroller guiderail upward until fully
unfolded (fig. 2).
ATTACHING AND REMOVING THE WHEELS
In order to attach the front wheels, push their hubs into
the handles on the ends of the front tubes (fig. 3). In order to
remove the wheel, press the button on the back of the wheel
and pull the hub from the handle (fig. 4).
The front wheels are articulated, which can also be locked
in a forward facing position. In order to
lock the wheels in a forward facing position, move up the
button located on the front of the wheel (fig. 5). In order to
release the wheels, move the button down.
In order to attach the rear wheels, push their hubs into the
handles on the rear suspension of the
stroller (fig. 6). In order to remove the wheels, pull down the
metal lock at the bottom of the handle
and slide the hub (fig. 7).
ADJUSTING THE HEIGHT WITH THE HANDLE
The push chair has a telescopic height adjustment handle.
To make adjustments, press the button in the central part and
then set to the correct height (fig. 8).
PARKING BRAKE
The pram is equipped with a rear parking brake. To engage
the brake, press its lever down (Fig. 9). In order to disengage
it, lift the lever.
NOTE! Before starting to push the pram, make sure that
the brake has been disengaged.
NOTE! Always engage the safety brake, when you leave
the pram on an inclined surface.
NOTE! The brake is not designed for slowing down.
It should be engaged after the pram has been stopped
completely.
NOTE! The pram is not designed for running.
ATTACHING AND REMOVING THE CARRYCOT
In order to attach the carrycot press it into the pram frame
so that the adapters on both sides of the carrycot lock onto
the catches on the pram frame (fig. 10). They will lock in
place automatically.
ATTENTION! Make sure the carrycot is attached correctly
prior to use.
To remove the carrycot press the buttons on the adapters
at the sides of the carrycot (fig. 11) and pull the carrycot
upwards.
ASSEMBLING AND DISASSEMBLING THE SEAT
The seat should be assembled and disassembled the
same way as for the carrycot (see ATTACHING AND
REMOVING THE CARRYCOT)( fig. 12, 13).
The seat may be assembled with its front and back facing
the movement direction.
NOTE! Before starting to use the pram make sure that the
seat has been assembled correctly.
ADJUSTING THE LEG REST
The pram is equipped with an adjustable leg rest. To move
it to the right position, press down the buttons on its both
sides (fig. 14).
RESTRAINT SYSTEM
The seat is equipped with a 5-point restraint system
(fig. 15). It should be used from the moment a baby starts to
sit by itself. Unfasten the belts, by releasing the forks from the
central buckle, seat the baby, adjust the length of the belts so
that they fit closely to the baby's body, without oppressing it,
and then fasten the forks of all the belts to the central buckle.
The seat has an additional crotch strap which should be
attached to the safety bar using snaps (fig. 16). This is an
additional element and not be a substitute for using the 5
point safety harness.
NOTE! Always use the restraint system, if the baby can sit
by itself.
SAFETY BAR
To attach the bar, insert its tongues into the slots in
armrests (fig. 17). To remove it, push the buttons located on
the bottom of the slots (fig. 18).
The bar is adjustable. You can detach one of its ends and
move it sideways to place the baby inside the carriage (fig.
19).
NOTE: The bar is an extra element and you must still use
the five-element harness to secure the child.
BACKREST ADJUSTMENT
The stroller has 4-step adjustment of the backrest. In
order to lower the backrest, pull the lever on the rear of the
backrest and set the desired position (fig. 20). In order to
raise the backrest, just push it upward. It locks automatically
in that position.
FOLDING THE STROLLER
To fold the stroller, slide the small button on the back of
the guide in the direction of the arrow (fig. 21A). Hold it and
simultaneously, press the large button located in the centre of
the handle. Then push the handle in the direction of the arrow
as far as it will go (fig. 21B). At this point the mechanism will
be unblocked and the frame will start to fold. Push the handle
to the ground until fully folded (fig. 22). Insert the telescopic
handle all the way to lock the frame in the folded position
(fig. 23).
9