M-system MVK-60 Instrucciones De Uso página 3

that purifies the air sent back into the room.
In the Ducting version (Fig. 2), cooking vapours and odours
are conveyed straight outside by a disposal duct which
passes through the wall/ceiling. Use of charcoal filter is
therefore unnecessary.
According to the model you have bought, the appliance can
include 1 or 2 motors. In the I motor version the flange for
the air to be exhausted has not got a central position, but
it is slightly on the left.
INSTALLATION
-----------------------------------------------------------
Before assembling, in order to manoeuvre the appliance
more easily, take off the grease grille (Fig. 3): pull the front
of the grille upwards; desinsert the back from its seat.
IMPORTANT: So as not to damage your product, during
installation USE ONLY THE SCREWS PROVIDED. Make
sure these are used as shown in the following instructions.
To compensate possible depth voids between the appliance
and the wall, a plastic SPACING BAR to be fixed at the
back of the appliance by means of the three screws A is
included (Fig.4). The 3 screws A to be used are contained
in the accessory bag attached to the plastic spacing bar.
Cut the spacing bar according to the distance to be
adjusted.
Assembly under a pensile cupboard
The following operations are essential for as-sembly:
– Install the wiring system
– Prepare the air venting hole if your appliance is to be
installed in the Ducting version.
Fixation as indicated in Fig. 5:
Using the relative template make the 4 necessary fixing
holes in the bottom of the cupboard and cut the air venting
hole.
Move the hood close to the bottom of the wall unit and then
connect the two units by means of the 4 self-tapping
screws supplied together with the appliance.
Fixation with brackets as in Fig. 6 (optional):
Take the two brackets (S) out of the accessory bag
together with the 8 screws provided. Fit the brackets to
the wall unit being careful to position these correctly; for
this operation use the 4 longer screws. At this point,
secure the appliance to the brackets using the 4 shorter
screws.
Ducting version: connect the flange of the hood with the air
venting hole made previously in the wall/ceiling by means
of an adequate tube. Make the electrical connection of the
hood by means of the power supply cable. Assemble the
grease grille with the hood, inserting it obliquely (making the
front side go upwards).
Filtering version: connect a proper pipe to the flange of the
hood so that the air is sent outside the pensile and sent back
into the room. Make the electrical connection of the hood
by means of the power supply cable. Set the charcoal filter
(Fig. 7A) inside the grease grille blocking it by means of the
2 supplied metal wires (F), as indicated in Fig. 7; the 2 metal
wires must be threaded into the relevant slots.
Assemble the grease grille with the hood, inserting it ob-
liquely (making the front side go upwards).
OPERATION
-----------------------------------------------------------
Controls (Fig. 8):
A = ON/OFF 1st speed switch
B = II speed switch
C = III speed switch
The motor is automatically ON or OFF by opening/
closing the truck (unless switch A is on 0). Opening
the truck the motor works according to last speed
registered.
D = Light switch:position A (automatic), the light are
automatically regulated ON or OFF by the opening/
closing of the truck. Position M (manual), the light is
on. Position 0, the light is off.
In case the hood is a filtering version one, it is necessary
to change the charcoal filter(s) according to utilization
about every six month. To remove the filter:
– open the truck pulling it first downwards, then towards
the front.
– take off the grease grille: pull the front of the grille
upwards; desinsert the back from its seat.
– take off the charcoal filter (A) from the inside of the
grease grille taking off the 2 metal wires F (Fig. 7) that
blocks it.
Light bulb
- If the fluorescent light or incandescent lamps need
changing, slacken the light cover by disconnecting the
screw and remove the bulb itself (Fig. 9). Replace with a bulb
of the same type.
- To change the rectangular halogen bulbs open the cover
and remove the bulb without touching it with bare hands
(Fig.10). Replace with a bulb of the same type.