DeWalt D25901 Manual De Instrucciones página 8

English

WARNING: Be aware of the location of pipework
and wiring.

WARNING: Apply a pressure of approx. 44–66 lbs.
(20–30 kg.) to the tool. Excessive force does not speed
up chiselling but decreases tool performance and may
shorten tool life.
Proper Hand Position (Fig. E)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the bail/
loop style auxiliary handle 5
main handle 2 .
Fig. E
5
Switching On and Off (Fig. A)
To turn the tool on, set the on/off switch
turn the tool off, set the on/off switch
Demolition, Chasing and Channelling
(Fig. A)

WARNING: Ensure that the cutting edge does not
show discoloration caused by too much pressure. This
may impair the hardness of the accessory.
Various types of chisels are available as an option.
1. Select the appropriate chisel. Clean and grease its shank.
2. Insert the chisel and check whether it is properly locked.
3. Set the desired impact energy level (D25901).
4. Fit and adjust the bail/loop style auxiliary handle
make sure it is firmly tightened.
5. Hold the tool with both the main handle and the bail/
loop style auxiliary handle and switch on. The tool now
runs in continuous operation.
6. Always switch off the tool when work is finished and
before unplugging.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
6
with the other hand on the
2
1 to position 1. To
to position 0.
1
5 and
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1‑800‑4‑D WALT (1‑800‑433‑9258) or visit our website:
e
www.dewalt.com.
Repairs

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D WALT authorized service center.
e
Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
WARRAnTY sERViCE: Registering your product will
•
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of
warranty coverage and warranty repair information, visit
WALT
e
WALT Industrial
e
WALT factory
e