Publicidad
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by authorised
Service Agents.
The handle lock must always be engaged when transporting the
mitre saw.
Ensure that the machine is always stable and secure (e.g. fixed to
a bench)
Keep the floor area free of loose material e.g. chips and cut-offs.
Before using the tool please read the instructions. If possible have
the tool demonstrated.
Always use the protective shields on the machine.
Only use the saw with guards in good working order and properly
maintained, and in position.
Do not clamp the protective swing guard.
Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area whilst the machine is running and the saw
head is not in the rest position.
Never reach into the danger area of the machine when it is running.
Any faults with the machine, including any related to the safeguard
or the saw blades, must be reported to the persons in charge of
safety as soon as the faults are discovered.
Do not use any flanges other than those supplied or indicated in the
instruction manual to secure the saw blade.
Replace the table insert when worn
Do not use saw blades which are damaged or deformed
Do not use saw blades not corresponding to the key data given in
these instructions for use.
Do not use saw blades made of high-speed steel.
Only use saw blades which have been properly sharpened. It is
essential to adhere to the maximum speed specified on the saw
blade.
Transport and store the tools in a suitable receptacle.
It is necessary to select a saw blade which is suitable for the
material being cut.
Never use the mitre saw to cut materials other than those specified
in the instruction manual.
Long workpieces must be adequately supported.
Stock having a round or irregular cross section (such as firewood)
must not be cut, as it can not be securely held during cutting. When
sawing thin stock layed on edge, a suitable auxilary fence must be
used for firm support.
Do not stare into beam. Do not point laser light at other persons.
Do not view directly into beam with optical instruments (binocular,
telescope).
Do not point laser at reflective surfaces, Avoid exposure to laser
radiation. Laser may emit hazardous radiation.
Do not replace the installed laser with a different type.
Any repairs must only be carried out by the authorized service
agent.
Do not use this tool 's dust extraction as a vacuum cleaner to pick
up anything, such as hardness work pieces or nails etc. it will cause
the fan damage.
Deutsch
SPECIFIED CONDITIONS OF USE
The mitre saw can be used for sawing solid wood, bonded wood,
glued veneer, materials similar to wood, aluminium profiles, Non-
ferrous metals and plastics.
Do not use this product in any other way as stated for normal use.
RESIDUAL RISk
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise in use and the operator should pay special
attention to avoid the following:
• Impairment of hearing, restrict exposure and wear appropriate
hearing protection.
• Measures that can be taken by operator to possibly reduce the
effects of vibration and limit the amount of exposure.
• Health hazards caused by breathing dust developed when
sawing wood, wear a mask if necessary.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" fulfills all the relevant regulations and the
directives 2011/65/EU (RoHs), 2004/108/ EC, 2006/42/EC and the
following harmonized standards have been used:
EN 61029-1:2009 + A11:2010
EN 61029-2-9:2009
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-11:2000
Winnenden, 2013-10-01
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
MAINS CONNECTION
Connect only to single-phase AC current and only to the system
voltage indicated on the rating plate. It is also possible to connect
to sockets without an earthing contact as the design conforms to
safety class II.
A power spike causes voltage fluctuations and may affect other
electrical products in the same power line. Connect the product
to a power supply with an impedance equal to 0.3Ω to minimize
voltage fluctuations. Contact your electric power supplier for
further clarification
EN
English
21
Publicidad
