Safety Instructions; Double Insulation - Black and Decker KS890E Manual De Instrucciones

Scorpion Saw user manual

SAFETY INSTRUCTIONS

Warning! When using electric tools, the following
basic safety precautions should always be taken to
reduce the risk of fire, electric shock and personal
injury. Read all these instructions before attempting to
operate the product and save this booklet.
For safe operation:
• Keep the work area clean. Cluttered areas and
benches invite injuries.
• Consider the work area environment. Do not expose
the power tool to rain and do not use in damp or wet
locations. Keep the work area well lit. Do not use
the power tool where there is a risk to cause fire
or explosion.
• Guard against electric shock. Avoid body contact,
where possible, with earthed or grounded surfaces
(e.g. pipes, radiators, ranges and refrigerators).
• Keep children away. Do not let visitors touch the
tool or extension cord. All visitors should be kept
away from the work area.
• Store idle tools. When not in use, tools should be
stored in a dry, high or locked place, out of reach
of children.
• Do not force the tool. It will do the job better and
more safely at the rate for which it was intended.
• Use the right tool. Do not force small tools or
attachments to do the job of a heavy duty tool.
Do not use the tool for purposes not intended; for
example, do not use a circular saw or Scorpion Saw
to cut tree limbs or logs.
• Dress properly. Do not wear loose clothing or
jewellery as they can be caught in moving parts.
Rubber gloves and non-skid footwear are
recommended when working outdoors.
Wear protective hair covering to contain long hair.
• Use safety glasses. Use a face or dust mask as
well, if the operation is dusty or if the tool is being
used in enclosed spaces.
• Do not abuse the cord. Never carry the tool by its
cord or yank it to disconnect it from the socket. Keep
the cord away from heat, oil and sharp edges.
• Secure the work. Use clamps or a vice to hold the
work. It is safer than using a hand and it frees both
hands to operate the tool.
• Do not overreach. Keep proper footing and balance at
all times.
• Maintain the tool with care. Keep a cutting tool
sharp and clean for better and safer performance.
Follow the instructions for lubricating and changing
accessories. Inspect the tools cord periodically
and, if damaged, have repaired by an authorised
service facility. Inspect the extension cord
periodically and replace if damaged. Keep the
handles dry, clean and free from oil and grease.
• Disconnect the tool when not in use, before
servicing and when changing accessories such as
blades, bits and cutters.
• Avoid unintentional starting. Do not carry a
plugged-in tool with a finger on the switch.
Ensure the switch is off when plugging in.
• Use an outdoor extension cord. When a tool is
used outdoors, only use an extension cord
intended for outdoor use and so marked.
• Stay alert. Watch what you are doing, use common
sense and do not operate the tool when tired.
• Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine whether it will
operate properly and perform its intended
function. Check for alignment of moving parts,
free running of moving parts, breakage of parts,
mounting and any other conditions that may affect
its operation. A guard or other part that is
damaged should be properly repaired or replaced
by an authorised service centre unless otherwise
indicated in the product booklet. Have defective
switches replaced by an authorised service
centre. Do not use the tool if the switch does not
turn it on and off.
• Warning! The use of any accessory or attachment,
other than recommended in the product booklet,
may present a risk of personal injury.
• Have the tool repaired by a qualified person.
The electrical tool is in accordance with the
relevant safety requirements. Repairs should only
be carried out by qualified persons using original
spare parts, otherwise, this may result in
considerable danger to the user.
Save these instructions!

DOUBLE INSULATION

The tool is double insulated. This means that all
the external metal parts are electrically insulated
from the mains power supply. This is done by
placing insulation barriers between the electrical
and mechanical components making it
unnecessary for the tool to be earthed.
3