Husqvarna TS 354X Manual De Repuestos página 7

TRACTOR - MODEL NO. TS 354X (96043029600), PRODUCT NO. 960 43 02-96
CHASSIS
KEY PART
NO. NO. DESCRIPTION
2 580 43 44-01 Drawbar
3 532 44 44-81 Applique Sub Asm.
5 590 74 88-29 Dash
14 532 44 11-77 Hood
15 585 42 03-01 Lens LH
18 587 52 34-01 Grille
25 585 42 02-01 Lens RH
36 817 06 05-12 Screw 5/16-18 x 3/4
37 532 44 12-08 Fender
58 532 19 43-14 Bracket Fender
68 539 99 08-58 Screw 5/16-18 x 1/2
125 581 68 48-01 Clip Fuel Line
130 532 41 63-58 Screw #10 x 0.750 BOS Thread
137 532 40 75-90 Bumper Dash
146 581 85 79-01 Bolt
150 532 43 97-74 Duct Air
151 532 43 66-70 Bracket Pivot Hood
152 532 43 98-70 Shield Browning/Debris
159 817 00 06-12 Screw HexWsh Thdr 3/8-16 x 3/4
161 532 43 99-29 Fuel Window
162 532 14 24-32 Screw Hex Wsh Hi-Lo 1/4 x 1/2
165 532 19 43-30 Bracket Support Tank
175 590 60 77-02 Crossmember
176 532 40 07-76 Screw 10-24 x 5/8 Wshd Qdrx
177 532 19 52-28 Bushing Steering
180 593 34 63-02 Chassis
182 532 40 68-59 Dash Lower
183 874 52 05-20 Bolt 5/16-18 x 1-1/4
189 817 00 05-12 Screw 5/16-18 x 3/4
191 586 18 28-01 Insert Reflective RH
194 873 90 05-00 Nut Lock Hex Flange 5/16-18
KEY PART
NO. NO.
196 532 43 96-74 Console Asm. Deck Lift
199 532 19 82-59 Plate Deck Lift
202 532 43 97-28 Vent Side Hood RH
203 532 43 97-27 Vent Side Hood LH
204 532 43 57-14 Vent Asm Hood Top
205 532 43 97-30 Skirt Hood Side RH
206 532 43 97-29 Skirt Hood Side LH
207 585 42 00-02 Bezel RH
208 585 42 01-02 Bezel LH
214 532 19 91-45 Clip Retainer
217 532 40 91-67 Rod Pivot
221 532 19 89-09 Reflector LH
228 532 19 51-61 Stud Fastener
235 532 40 61-29 Spacer Fender
236 873 93 05-00 Nut Center Lock 5/16-18 unc
281 817 00 06-16 Screw 3/8-16 x 1
296 585 42 05-01 LED Light LH
297 586 18 29-01 Insert Reflective LH
299 585 42 04-01 LED Light RH
306 873 90 06-00 Nut Lock
335 532 44 82-04 Cover RH
336 532 44 53-09 Cover LH
350 532 44 51-43 Clip X-mas Tree
375 586 90 82-01 Dash Clip-On Bumper
378 590 84 98-01 Bushing Flange Plastic
379 593 20 69-02 Chassis Plate Reinforcement
- - 532 43 18-82 Kit Guard Brush
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
7
DESCRIPTION