C -Installation Of Your Cooler; Selecting The Place Of Installation; Positioning; Installation - Ugur USS 100 SC Guia Del Usuario

C -INSTALLATION OF YOUR COOLER.

Selecting the place of installation

The operating environment of the product is very important for the smooth operation of your product. While selecting
the operating environment,
• Do not place your product exposed to outdoor environment (on the street, avenue etc.)
• Place the product at least one (1) meter away from heat resources (stove, radiator, electric heater etc.) (Picture 1)
• Do not place it opposite to the air conditioner chutes, under fans and direct door and window openings. (Picture 2)
• Do not expose to direct sunlight. Operation ratio will increase if sunlight comes to the cooler's glass. That means an
increase in the energy consumption.
• Be careful for not obstructing lower shutter of the product with materials such as cardboard, box etc. for a proper
cooling.
• Air intake and outlet must absolutely be fluent and free for proper operation of the compressor section of your pro-
duct.
• While approaching your product to the wall, be careful that there is a gap of 150 mm (15 cm) between the wall and
back of your cooler
WARNING!
Çok yüksek nemli ortamlarda tahliye suyunun taşması tehlikesine karşı, soğutucunuzun bulunduğu bölge zemin
ve duvarının sudan zarar görmeyecek bir yer olmasına özen gösteriniz.
Uğur Yetkili Servis tarafından gerçekleştirilen montajlarda; Uğur Yetkili Servisi, montaj için uygun olan yer konu-
sunda tüketiciyi bilgilendirecek ve öneride bulunacak, ancak montajın gerçekleştirileceği yer ile ilgili son kararı
tüketici verecektir. Uğur Yetkili Servis tarafından da bahsi geçen süreç, ilgili montaj servis formunda belirtilecektir.
Tüketicinin verdiği son karara bağlı olarak ürünün konulacağı yerden kaynaklı herhangi bir zararın ortaya çıkması
halinde bahsi geçen zararla ilgili tüm sorumluluk tüketiciye ait olacaktır.
EN
Your cooler gives the best cooling performance according to the climate condition under the conditions given below.
Therefore, be careful that the temperature of the environment where your cooler will operate is at these levels.
Climate Class Temperature Range
Class 3 16 °C ile 25 °C
Class 4 16 °C ile 30 °C
Class 5 16 °C ile 40 °C
Climate Class of your product is indicated on the technical specification label on the product.
Picture 1
Humidity
%60 Rh
%55 Rh
%45 Rh
Picture 2
40
C -INSTALLATION OF YOUR COOLER.

Positioning

Possible placement positions:
1. In a way that the back side alone is opposite to the wall; be careful that there is a gap of 150 mm (15 cm)
between the wall and your cooler. (Picture 3)
2. In a way that is place to a corner; when you place to a corner, leave a gap of 150 mm (15 cm) behind. You can
lean the side corresponding to the corner to the wall.
The most important point to be considered in all cases of product placement is not to obstruct ventilation of
the compressor assembly.
Without exposing your product to any slope, place and operate it in a manner that it is on its feet or wheels.
The freer the compressor assembly ventilation is, the better the device will run.
Picture 3

Installation

Before positioning, remove and disassemble all packaging materials and bottom wooden pallet of the product.
(It may be necessary to lift the cooler for removing the bottom pallet).
Insert the parts inside your product according to the installation instructions. Only use genuine Uğur spare parts.
Inauthentic spare parts may constitute danger for you and damage your product.
Place the product anywhere you desire. Consider the placement rules written in the manual while positioning
the product.
Balance your product in width and in depth by means of a water gauge. Perform balancing operation by using
adjustable feet at the bottom front of your cooler. (Picture 4)
In models with wheels (optional), wheel brake (optional) must be locked or if there is no wheel brake, it must be
guaranteed that the device will not move after the positioning of the product.
Picture 4
41
EN