Functional Description - Milwaukee 5426-21 Manual Del Operador

FUNCTIONAL DESCRIPTION

1
13
12
1. Bit holder
2. Rear side handle
position
3. Mode selector
4. Trigger lock-on
(5446-21 only)
5. Trigger
6. Handle
7. Hammer speed control
8. Power indicator
9. Service indicator
10. Side handle
11. Side handle ball (5446-21 only)
12. Clamp
13. Depth gauge rod
GROUNDING
Improperly connecting the ground-
WARNING
ing wire can result in the risk of
electric shock. Check with a qualified electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the tool. Never remove the grounding
prong from the plug. Do not use the tool if the
cord or plug is damaged. If damaged, have it
repaired by a MILWAUKEE service facility before
use. If the plug will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Grounded Tools (Three-Prong Plugs)
Tools marked "Grounding Required" have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet
(See Figure A). If the tool should electrically mal-
function or break down, grounding provides a low
resistance path to carry electricity away from the
user, reducing the risk of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool's grounding
system and must never be attached to an electrically
"live" terminal.
Your tool must be plugged into an appro-
priate outlet, properly installed and
grounded in accordance with all codes
and ordinances. The plug and outlet
should look like those in Figure A.
3
2
10
9
8
11
Fig. A
Double Insulated Tools (Two-Prong Plugs)
Tools marked "Double Insulated" do not require
4
grounding. They have a special double insulation
5
system which satisfies OSHA requirements and
complies with the applicable standards
of Underwriters Laboratories, Inc., the
Canadian Standard Association and
the National Electrical Code. Double
Insulated tools may be used in either
6
of the 120 volt outlets shown in Figures
B and C.
7
WARNING
removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always use a side
handle when using this tool. Always brace or
hold securely.
Adjusting the Side Handle Position
1. Loosen the side handle by unscrewing the side
handle grip (5426-21) or ball (5446-21) until the
side handle rotates freely.
2. Rotate the side handle to the desired position.
3. Tighten the side handle grip or ball securely.
1. Remove the side handle by unscrewing the side
handle grip until it comes free.
2. Screw the side handle into the alternate location.
3. Tighten the side handle grip securely.
Setting the Depth Gauge
1. Press in the clamp lever.
2. Slide the depth gauge rod backward or forward
until it is set for the desired depth.
NOTE: The drilling depth is the distance between
the tip of the bit and the tip of the depth gauge rod.
Drilling
Depth
3. Release the clamp lever.
WARNING
rotating or while the bit is falling from the chuck.
Installing Drill Bits and Chisels
Be sure that the shank of the bit is clean. Dirt particles
may cause the bit to line up improperly. Do not use
bits larger than the maximum recommended capacity
of the drill because gear damage or motor overload-
ing may result. For best performance, be sure that
the bit is properly sharpened and the shank is lightly
greased before use.
4
ASSEMBLY
To reduce the risk of injury, always
unplug tool before changing or
Moving the Side Handle
(Cat. No. 5426-21)
To reduce the risk of injury, do not
grasp the bit while the chuck is
Fig. B Fig. C