Suzuki 990D0-04K80-CRB Manual De Instalación

®
Description: Carbon rear fender - matt finish
Applications: GSX-S1000/F AL6
Ref. Description
Part List
1
Carbon rear fender
2
Mounting instructions
Ref. Description
Tools Required
1 Torque wrench
2 Ratchet
3 Socket (10 and 36mm)
4 Hex bit socket (5mm)
5 Wrench tool (10 and 12mm)
6 Thread Lock (middle strength)
 WARNING / 
! ! CAUTION / NOTICE / NOTE.
Important
Please read this manual and follow its instructions carefully. To emphasize special
information, the symbol 
have special meanings. Pay particular attention to messages highlighted by these
signal words:
Indicates a potential hazard that could result in death or serious injury.
Indicates a potential hazard that could result in minor or moderate injury.
Indicates a potential hazard that could result in vehicle or equipment damage.
NOTE: indicates special information to make maintenance easier or instructions
clearer.
SUZUKI Deutschland GmbH, Suzuki-Allee 7, D-64625 Bensheim
1
MOUNTING INSTRUCTIONS
Part Number: 990D0-04K80-CRB
Mounting Time:
Qty.
1
1
! and the words WARNING, CAUTION, NOTICE and NOTE

WARNING
!

! CAUTION
NOTICE
Precautions for
Installation
30 Min
1 2
1 2
Tightening
3 4
Torque
5 6
Mounting
Care and
Maintenance
Inspection
1. Check that the kit includes all the parts listed on the first page.
2. Check each part in the kit for scratches or any form of damage.
3. Park the vehicle on level ground.
4. Remove the ignition key from the switch and store it in a safe place.
5. Protect any items removed or to be installed from scratches by placing them on a
soft cloth first before putting them on the ground.
6. Use care not to cause any damage to the body of the vehicle during installation
of the accessory.

! CAUTION
If you do not feel technical qualified to install this product on your own,
please consult with your nearest SUZUKI dealer.
Tighten bolts to the torque indicated in the right
table as standard value unless otherwise explicitly
specified. The value shows conventional or "4"
marked bolt tightening torque. For other bolts not
listed in the table, please refer to owners manual.
NOTE: Read these instructions carefully before assembly and examine
whether all parts are enclosed in accordance with the parts list.
1. Disassemble rear wheel according to owner's manual.
2. Detach brake tube (C) from metal bracket (B). (Fig 2)
3. Remove hex washer head screw (M6x12) (D) and button socket head screws
(M6x12) (E) 3 pcs. (Fig 3)
4. Remove original metal bracket (B). (Fig 4)
5. Remove original rear fender (A). (Fig 5)
6. Install carbon rear fender 1 and original metal bracket (B) using hex washer
head screw (M6x12) (d) and button socket head screws (M6x12) (E). (Fig 6)
Tightening torque: screw (M6x12mm): 5.5Nm (4.0lbf-ft).
NOTE: Put some threat lock on screw.
7. Clamp brake tube (C) to original metal bracket (B). (Fig 7)
8. Assemble rear wheel according to owner's manual.
NOTE: Check the tightening torque of each bolt on a regular basis and tighten
as needed.
To clean, rinse carbon part with water to remove grit and soften dirt. Use a mild non-
abrasive liquid soap, plenty of warm water, and a clean flannel cloth or soft chamois.
Rinse well to remove all soap residue. Pat dry do not wipe.
Due to mounted SUZUKI Genuine Accessories the service and maintenance flat rate
might be affected. Dismounting/Mounting of SUZUKI Genuine Accessories is
possibly necessary for service and maintenance.

! CAUTION
In case of fall, check all screws and parts. Check also the tightness.
If necessary replace screws or damaged parts.
The holder of the vehicle should always be in possession of the mounting instruction.
SUZUKI GENUINE ACCESSORIES
Diameter Tightening Torque
N·m
(mm)
kgf-m lbf-ft
5 3.0 0.3 2.2
6 5.5 0.55 4.0
8 13.0 1.3 9.5
10 29.0 2.9 21.0
12/2015 ENG