Stanley STMT74840-840 Manual De Instrucciones página 12

English
WARNING
Stop using the tool immediately if any of the following problems occur. Serious personal injury
could occur. Necessary repair or replacement must be carried out by qualified and trained
technician of authorized service location.
Possible Cause
Problem
Grit or gum in tool.
No oil in tool.
Low air pressure.
Air hose leaks.
Tool runs slowly or
will not operate.
Pressure drops.
Worn rotor blade.
Moisture blowing out
of tool exhaust.
22
Corrective Action
1. Flush the tool with air tool oil or
gum solvent.
2. Lubricate the tool according to the
lubrication instructions.
3a. Adjust the regulator on the tool to
maximum setting.
3b. Adjust the compressor regulator to tool
maximum of 90 PSIG.
4. Tighten and seal hose fittings if leaks
are found. Use sealing tape.
5a. Be sure the hose is the proper size. Long
hoses or tools using large volumes of air
may require a hose with an I.D. of 1/2 in.
or larger depending on the total length of
the hoses.
5b. Do not use a multiple number of hoses
connected together with quick-connect
fittings. This causes additional pressure
drops and reduces the tool power.
Directly connect the hoses together.
6. Replace rotor blade.
7.Water in tank: drain tank. (See air
compressor manual.) Oil tool and run
until no water is evident. Oil tool again
and run 1-2 seconds.
WARRANTY GUIDE
LIMITED LIFETIME WARRANTY STANLEY TOOLS
Except as specified below, Stanley Tools warrants this product to the original purchaser for the useful life of the product against
defects in material or workmanship. This LIMITED LIFETIME WARRANTY does not extend to products that have been improperly used,
altered, or repaired by any entity other that Stanley Tools.
Defective products will be replaced or repaired.
Limitations:
This Limited Lifetime Warranty:
• Does not extend to products that have been improperly used, altered, or repaired by any entity other than Stanley Tools.
• Does not cover damage due to normal wear.
• Does not extend to any claim of accidental injuries caused by wrong product usage.
• Stanley Tools makes no representations beyond those contained in this Limited Lifetime Warranty.
• Employees and agents of Stanley Tools have no authority to make representations of any sort beyond those contained in
this Limited Lifetime Warranty.
Exceptions:
The following products have limited warranty from the date of purchase:
• Torque Wrenches, Torque Multipliers, Torque Testers are warranted for 1 year, except for calibration which is warranted
for 90 days.
• Air tools warranted for 1 year.
• Laser line warranted for 2 years.
Claim procedure:
To use the warranty, the purchaser must have the purchase invoice and warranty form filled with requested information when applicable.
• Original invoice: Make sure that it is a valid document and was issued on the purchase date.
• The product must be used according to the Instruction Manual when applicable.
• Use the warranty claim when a product is determined to be deficient in materials or workmanship.
INTERPRETATION OF WARRANTY POLICY
Accidents
Tools damaged by being dropped, crushed by vehicles or other types of accidents, will not be considered in warranty.
Wrong Usage
The wrong usage of the tools is not covered by warranty. Examples of wrong usage are listed below:
• Blows, drops or external impacts.
• Ingress of foreign materials during operation (Example: Screws, metal parts, etc.).
• Lack of maintenance recommended in the instruction manual ( if applicable).
• Excess or fault of oil in pneumatic tools.
• Damage in the air connections due to transport over the hose in pneumatic tools.
• Using extensions that modify the lever arms.
• Using tools for inadequate works, example: Screwdrivers on screw heads not suitable for; etc.
• Use of non-original spare parts.
• Any modification made to the tool out of the original specification.
Use of improper accessories for the tool.
The use of improper accessories in our tools which can damage it will not be considered in warranty.
Parts worn out by normal use.
The parts worn out by normal use of the tool is not covered under warranty. Examples of these parts are: Seals
(o-ring), pistons, bearings, etc.
Doubts and Questions:
To ask questions or make use of the warranty, contact a representative of Stanley Tools.
23