Scheppach HM100MP Traducción De Las Instrucciones Originales De Funcionamiento página 28

Use the handle (1) to push back the machine head
•
(5) and fix it in this position if required (dependent
on the cutting width).
Place the piece of wood to be cut at the stop rail
•
(18) and on the turntable (16).
Lock the material with the clamping device (8) on
•
the fixed saw table (16) to prevent the material from
moving during the cutting operation.
• Push down the release lever (3) to release the ma-
chine head (5).
Press the ON/OFF switch (2) to start the motor.
•
With the drag guide (23) fixed in place:
•
use the handle (1) to move the machine head (5)
steadily and with light pressure downwards until
the saw blade (7) has completely cut through the
work piece.
With the drag guide (23) not fixed in place:
•
pull the machine head (5) all the way to the front.
Lower the handle (1) to the very bottom by applying
steady and light downward pressure. Now push the
machine head (5) slowly and steadily to the very
back until the saw blade (7) has completely cut
through the work piece.
When the cutting operation is completed, move
•
the machine head (5) back to its upper (home)
position and release the ON/OFF button (2).
Attention! The machine executes an upward
stroke automatically due to the return spring, i.e.
do not release the handle (1) after completing the
cut; instead allow the machine head to move up-
wards slowly whilst applying light counter pres-
sure.
8.5 Cross cut 90° and turntable 0° - 45° (Fig. 1,6,7)
The crosscut saw can be used to make crosscuts of
0° -45° to the left and 0° -45° to the right in relation
to the stop rail.
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (28) must be fixed in the outer
position.
Open the set screw (29) on the moveable stop
•
rail (28) and push the moveable stop rail (28) out-
wards.
The moveable stop rail (28) must be locked in a
•
position far enough from the inner position that the
distance between the stop rail (28) and the saw
blade (7) is no more than 5 mm.
Before making the cut, check that no collision
•
could occur between the stop rail (28) and the saw
blade (7).
Tighten the set screw (29) again. (2x 8.6 + 8.7)
•
Use the handle (13) to adjust the rotary table (16)
•
to the desired angle. The pointer (14) on the rota-
ry table (16) must match the desired angle on the
scale (15) on the fixed saw table (17).
• Tilt the locking lever (13) back up again to fix the
rotary table (16) in place.
Cut as described under section 8.3.
•
28 GB
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1,2,6,8)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28) must be fixed at the outer
position.
Open the locking lever (29) for the adjustable stop
•
rail (28) and push the adjustable stop rail outwards.
• The adjustable stop rail (28) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (28) and the saw
blade (7) amounts to a maximum of 5 mm.
Before making a cut, check that the stop rail (28)
•
and the saw blade (7) cannot collide.
Secure the locking lever (29) again.
•
• Move the machine head (5) to the top position.
Fix the rotary table (16) in the 0° position.
•
Loosen the set screw (22) and use the handle (1)
•
to angle the machine head (5) to the left, until the
pointer (20) indicates the desired angle measure-
ment on the scale (19).
Re-tighten the fixing screw (22).
•
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 1,2,6,9)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the
right in relation to the stop rail (double mitre cut).
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28) must be fixed at the outer
position.
Open the locking lever (29) for the adjustable stop
•
rail (28) and push the adjustable stop rail outwards.
• The adjustable stop rail (28) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (28) and the saw
blade (7) amounts to a maximum of 5 mm.
Before making a cut, check that the stop rail (28)
•
and the saw blade (7) cannot collide.
Secure the locking lever (29) again.
•
• Move the machine head (5) to its upper position.
Release the rotary table (16) by loosening the set
•
screw (26).
Using the handle (13), set the rotary table (16) to
•
the desired angle (refer also to point 8.4 in this
regard).
• Re-tighten the set screw (26) in order to secure
the rotary table.
Undo the locking screw (22) and use the handle
•
(1) to tilt the machine head (5) to the left until it co-
incides with the required angle value (in this con-
nection see also section 8.6).
Re-tighten the fixing screw (22).
•
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3)
The cutting depth can be infinitely adjusted using
•
the screw (26). To do this loosen the knurled nut
on the screw (26). Turn the screw (26) in or out to