General Information; Unpacking; Accessory Box; Assembly - Generac GP Serie El Manual Del Propietario

General Information

1.1 UNPACKING

• Remove all packaging material.
• Remove separate accessory box.
• Remove the generator from carton.

1.1.1 ACCESSORY BOX

Check all contents. If any parts are missing or damaged, locate an
authorized dealer at 1-888-436-3722.
• 1 - Owner's Manual
• 1 - Quart Oil SAE 30
• 2 - Never-Flat Wheels
• 1 - Hardware Bag (containing the following):
2 -Rubber Bumpers
2 - Flat Washers (for Foot)
4 - Carriage Bolts
2 - Axle Pins
2 - Flat Washers (for Axle Pins)

1.2 ASSEMBLY

The generator requires some assembly prior to using it. If
problems arise when assembling the generator, please call the
Generator Helpline at 1-888-436-3722.

1.2.1 ASSEMBLING THE ACCESSORY KIT

The wheels are designed into the unit to greatly improve the
portability of the generator.
The wheels are not intended for over-the-road use.
1. Refer to Figure 1 and install the Wheels as follows:
• Slide the Axle Pins through the Wheels, Flat Washers, and Wheel
Brackets on the frame.
• Insert the Cotter Pins through the Axle Pins then bend the tabs (of
the Cotter Pins) outward to lock into place.
2. Refer to Figure 1 and install the Frame Foot and Rubber
Bumpers as shown.
• Slide the Rubber Bumper studs through the Frame Foot then install
the Locking Flange Nuts.
• Slide the Hex Head Bolts through the Flat Washers then through the
holes in the Frame Rail.
• Slide the Frame Foot onto the Hex Head Bolts then install the
Locking Flange Nuts.
3. Refer to Figure 2 and install the Handles as shown.
• Remove the top Curved Head Bolts and Cap Nuts (Cap Nuts will be
re-used).
• Align and slide the Handle Assemblies over the Frame Tube.
• Slide the Carriage Bolts through the Handle Assemblies & Frame
Tube then install the Locking Cap Nuts.
4
• 1 - Left Handle Assembly
• 1 - Right Handle Assembly
• 1 - Frame Foot
2 - Hex Head Bolts
4 - Locking Flange
Nuts
2 - Locking Cap Nuts
2 - Cotter Pins
NOTE:
Figure 1 – Wheel Assembly
2X COTTER PIN
2X FLAT WASHER
2X WHEEL
2X AXLE PIN
FOOT
2X RUBBER BUMPER
Figure 2 – Install Handle Kit

2.1 KNOW THE GENERATOR

Read the Owner's Manual and Safety Rules before operating
this generator.
Compare the generator to Figures 3 through 5 to become
familiarized with the locations of various controls and adjustments.
Save this manual for future reference.
1. 120 Volt AC, 20 Amp, Duplex Receptacle – Supplies electrical
power for the operation of 120 Volt AC, 20 Amp, single-phase,
60 Hz electrical lighting, appliance, tool and motor loads.
2. 120/240 Volt AC, 30 Amp Locking Receptacle – Supplies
electrical power for the operation of 120 and/or 240 Volt AC,
30 Amp, single-phase, 60 Hz, electrical lighting, appliance,
tool and motor loads.
3. Circuit Breakers (AC) – Each receptacle is provided with a
push-to-reset circuit breaker to protect the generator against
electrical overload.
4. Hourmeter – Tracks hours of operation.
2X HEX HEAD BOLT
2X FLAT WASHER
4X LOCKING FLANGE NUT