Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

π
H-7093, H-7094
FORKLIFT STROBE LIGHT
TOOLS NEEDED
5/16" Wrench
Pedestrian Safety Light x 1
1. To operate, hardwire light to a switched power
source so light is either powered all times the truck is
on or when the forklift is put into drive or reverse.
NOTE: All hardwiring should be performed by
a qualified electrician. If unsure of the correct
electrical hookup location, contact local
forklift dealer. Length of wire needed will vary
by forklift. Extension wire may be necessary.
The negative (black) wire should connect to
negative side of the battery. On certain trucks,
this may be the frame. If you are uncertain
whether the frame is the negative/ground or
FOR MAGNET MOUNTING
1.
Attach strobe light to metal cage. (See Figure 1)
2. Ensure light is securely mounted before moving your
vehicle.
FOR BOLT-ON MOUNTING
1.
Select a location to install strobe light.
2. Align mounting plate holes with strobe light holes on
opposite side of cage.
3. Use bolt and nut to connect strobe light through
mounting plate. Do not fully tighten. (See Figure 2)
4. Repeat with remaining two bolts and nuts.
5. Using screwdriver and 5/16" wrench, fully tighten all
three bolts and nuts.
PAGE 1 OF 3
1-800-295-5510
uline.com
Screwdriver
PARTS
Mounting Plate x 1
(For Bolt-On Installation Only)
OPERATION
INSTALLATION
Pour le français, consulter la page 3.
Bolt x 3
(For Bolt-On Installation Only)
know that it is not, a separate wire lead will be
required to run directly to the negative battery
terminal or main negative/ground of the truck.
CAUTION! DO NOT connect the forklift strobe
light to the drive motor leads or coils on
electric trucks. Connection should be made
to control wiring only. Use a volt meter prior
to connecting the light to verify the voltage.
A steady voltage must be observed with any
spikes in voltage remaining within allowable
limits.
Figure 1
Figure 2
Mounting
Plate
Para Español, vea página 2.
Nut x 3
(For Bolt-On Installation Only)
Bolt
Nut
0721 IH-7093

Publicidad

loading

Resumen de contenidos para Uline H-7093

  • Página 1 Para Español, vea página 2. Pour le français, consulter la page 3. π H-7093, H-7094 1-800-295-5510 uline.com FORKLIFT STROBE LIGHT TOOLS NEEDED 5/16" Wrench Screwdriver PARTS Bolt x 3 Nut x 3 (For Bolt-On Installation Only) (For Bolt-On Installation Only)
  • Página 2 π H-7093, H-7094 800-295-5510 uline.mx LÁMPARA ESTROBOSCÓPICA PARA MONTACARGAS HERRAMIENTAS NECESARIAS Llave de 5/16" Desarmador PARTES 3 Pernos 3 Tuercas (Solo para Instalación (Solo para Instalación 1 Soporte de Instalación con Pernos) con Pernos) 1 Luz de Seguridad para Peatones (Solo para Instalación con Pernos)
  • Página 3 π H-7093, H-7094 1-800-295-5510 uline.ca FEU STROBOSCOPIQUE POUR CHARIOT ÉLÉVATEUR OUTILS REQUIS Clé de 5/16 po Tournevis PIÈCES Boulon x 3 Écrou x 3 Plaque de fixation x 1 (pour installation avec (pour installation avec (pour installation avec boulons seulement) boulons seulement) Feu de sécurité...

Este manual también es adecuado para:

H-7094