FAAC XR2 433 C Manual Del Usuario página 5

T h e m a n u f a c t u r e r ,
EN
FAAC S.p.A. Soc. Unipersonale, declares
that the FAAC model XR2 433 C/XR2 868 C
radio receiver is in compliance with directive
2014/53/EU. The full text of the EU declaration
of conformity is available at the following Internet
address: http://www.faac.biz/certificates
INTENDED USE
The XR2 433 C/XR2 868 C is a two-channel radio re-
ceiver designed for automatic vehicle and pedestrian
entrance applications.
LIMITATIONS OF USE
XR2 433 C / XR2 868 C is compatible with the radio
protocols indicated in the table.
UNAUTHORISED USE
Uses other than the intended use are prohibited.
TECHNICAL DATA
Frequency
Radio protocol
Channels
Radio code memory
Power supply
Current consumption
Protection rating
Relay outputs
Relay contact rating
Mounting
Ambient
operating temperature
1. INSTALLATION
Fasten the enclosure to the support with two suitable
screws through the slots, or mount it on a DIN rail.
When wiring up, insert suitable cable glands into
the pre-cut holes to ensure the IP protection rating.
When finished, install the cover and secure it using
the two screws provided.
2. OPERATION
The XR2 can memorise up to 248 radio codes, divided
between the two available channels. When a chan-
nel is activated by the radio control, the relative relay
output is activated:
- CH1 = NO contact, pulse activation
- CH2 = NO contact, pulse or bistable activation
selectable via DIP switch (SW6)
XR2
XR2 433 C XR2 868 C
433.92 MHz 868.35 MHz
SLH/RC/DS SLH/DS
2
max 248 (channels 1-2)
"
/~
...
12 24 V
max 100 mA
IP44
2
0.5 A / 120VA
screws / DIN rail
-20 °C...+55 °C
SW6 ON
DIP 1
CH2 bistable
DIP 2
not used
In the bistable setting, contact CH2 switches state
and remains switched until it is activated again by
the radio control.
Radio codes of the protocols provided can coexist on
the same channel.
LED DL5 lights up when the receiver is powered.
3. PROGRAMMING
The SW1 and SW2 buttons memorise the radio
control for channel 1 (CH1) and channel 2 (CH2),
respectively.
Carry out the memorisation procedure holding the
radio control at least half a metre from the receiver.
■ MEMORISING THE FIRST SLH RADIO CONTROL
1. Press the button of the receiver that corresponds
to the channel that you wish to associate with
the radio control until the relative LED starts to
flash slowly (DL1->channel 1, DL2->channel
2). When the button is released, the LED con-
tinues to flash for 20 seconds, during which the
following steps 2 and 3 should be carried out.
2. On the SLH radio control: press buttons P1 +
P2 simultaneously, then release them, the
LED flashes.
3. Press and release the button of the radio control
to be memorised within 8 seconds. Make sure
that the flashing LED of the receiver becomes
steady 2 seconds before it switches off.
4. Press the button of the radio control that has just
been memorised twice in succession. The output
associated with the channel activates.
■ MEMORISING OTHER SLH RADIO CONTROLS
1. On the radio control that has already been memo-
rised, press buttons P1 + P2 simultaneously, then
release them, the LED flashes.
2. Within 8 seconds, press and hold the button that
has already been memorised, the LED lights up
with a steady light.
3. Bring the radio control that has already been
memorised, into contact face to face with the
new one to be memorised.
4. Press the button to be memorised on the new
radio control and make sure that its LED flashes
twice before turning off.
03
OFF
CH2 pulse
not used
532357 - Rev.A