Use - Supra TERTIO 55 Instrucciones De Instalación

6. USE

TAKE NOTE:
If a niche under the fireplace is being used as firewood storage,
never block it completely (a front opening with a section of at
least 600 cm² must remain free at all times).
Leave a space of at least 5 cm between the bottom of the
fireplace and the top of the logs.
To avoid any risk of burns, do not touch the appliance and use
the cool hand key to operate the controls.
Heat emitted through the vitro ceramic glass makes it necessary
to keep any material that could be damaged by heat (furniture,
wallpaper, carpentry, etc.) away from the hearth. A 2 m
clearance will avoid any risk.
FUEL
Wood
This high-performance appliance requires good quality fuel. Only
burn air-dried logs (2 to 3 years, stored in a sheltered and well-
ventilated place) with a maximum humidity of 15 to 20%.
Preferably hardwoods (birch, hornbeam, beech, etc.).
Avoid softwoods (lime, chestnut, willow, poplar),
Continuous use of resinous wood (pine, fir, etc.) as well as treated
wood (railway sleepers, carpentry offcuts, etc.) and household
waste (vegetable or plastic) is absolutely prohibited.
Never use small pieces of wood, boxes, woodchips or vine shoots
that could lead to sudden overheating.
ATTENTION:
The use of coal or coal derivatives, even
occasionally, is strictly prohibited. This appliance must not
be used to burn domestic waste.
DRAUGHT
The hot draught in the chimney flue must never be greater than 20
Pa. Ask your dealer to measure the draught when installing the
hearth. If the combustion air is not connected, any use of
controlled mechanical ventilation (CMV) may influence the
draught, even reversing it. For this reason, the extractor must be
running during measurement of the draught. If using CMV, an
outside fresh air intake is essential.
COMBUSTION AIR REGULATION
Air regulation Tertio 76 /76 VL
Closed
(0)
Air regulation Tertio 55 / 67 / 67 VL
Door handle
The handle is used to open and close the door.
- When the appliance is cold, directly by hand,
- when the appliance is hot, using the cold hand key.
Nominal output
(1)
Use of the cold hand key.
USE OF THE FAN (DEPENDING ON OPTION)
With natural convection, hot air builds up on the ceiling. The fan kit
circulates the ambient air to ensure a pleasant, even temperature
in the room. It includes a switch with 3 positions.
The fan kit is fitted with a thermostat that controls the operation of
the fan (On/Off). The thermostat is only active when the switch is
in position 'I' and the hearth is lit. The fan kit can operate on
setting 'II', whether the hearth is lit or not. The factory-set
thermostat temperature cannot be changed.
Fan modes
0 Off when the fire is burning low.
I Comfort For a pleasant 'cruising' speed .
II Turbo To heat up the room quickly
Refer to fan manual.
LIGHTING FOR THE FIRST TIME
Remove the self-adhesive labels, any possible blocking cards, and
make sure that the ash box is empty. It will take at least 2 weeks
for the chimney to start to operate normally.
- To light the fire from above, place 2 split logs in the hearth and
criss-cross a layer of kindling on top of the logs. Place a firelighter
on top of the wood and light it.
- To light it quickly from below, put down some crumpled paper,
then kindling on top and small pieces of wood on top of the
kindling.
Set the controls to the Light position (Table *). Light the fuel, close
the door and wait for embers to form. Once the fire is lit, load in
some wood and set the controls to the «nominal output» position,
Table (*). Lay the logs (at least 2 logs at the same time) towards
the back of the fireplace. It is best to load in the wood several
times rather than all at once.
If the outside temperature is very low, a heat «plug» may form
inside the flue, which is why it should be heated up gradually until
it reaches the normal draught rate.
OPERATION
Lighting the fire
To light your appliance, preferably use the top down method. This
Light fire lighting technique makes it possible to heat up the flue and to
S remove any blockages (negative pressure) that may form when
the weather is bad or cold, thereby preventing the air from blowing
back into the room when the fire is lit.
The procedure is as follows:
- Put the air combustion control to the maximum setting.
- Place 2 logs on the firebox grid.
- Place the kindling wood in the shape of a tower on top of the
logs.
- Put 1 or 2 fire-lighter cubes on the wood and set alight.
- Close the door.
For further information, view the Supra video on YouTube at:
https://www.youtube.com/watch?v=ebOr4vMj2Jo
TAKE NOTE: Never use petrol, alcohol or fuel-oil, etc.
Open
Close