RIDGID R09890 Manual Del Operador página 10

Ocultar thumbs Ver también para R09890:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATION
WARNING:
The nailer will not function properly if the selector
is not securely seated in either position ( ) or
(
). Always assure the selector is seated properly
to avoid an unexpected nail discharge and possible
serious personal injury.
 Reinstall battery and activate the tool by pressing the
worklight grip switch.
 Grip the tool firmly to maintain control. Position the nose
of the tool onto the work surface.
 Push the tool against the work surface to depress the
workpiece contact.
 Squeeze the trigger to drive a fastener.
NOTE: Hold trigger until drive cycle is complete. If depressing
the trigger does not drive a fastener, release the trigger and
lift the tool away from the workpiece, then replace and try
driving the fastener again.
CONTACT ACTUATION MODE
Contact actuation allows very fast repetitive fastener
placement.
 Remove battery pack from the tool.
 Slide the selector to position (
 Reinstall battery and activate the tool by pressing the
worklight grip switch.
 Grip the tool firmly to maintain control.
 Squeeze and hold the trigger. Push the tool against the
work surface to depress the workpiece contact and drive
a nail. To drive another nail, lift the tool and press the
contact against the work surface again.
NOTE: Hold trigger and keep workpiece contact
depressed until drive cycle is complete.
 Always remove your finger from the trigger when the
desired number of nails has been driven.
NOTE: In Contact Actuation Mode, the tool may also be
operated by depressing the workpiece contact against the
surface and squeezing the trigger.
WARNING:
During normal use the tool will recoil immediately
after driving a fastener. This is a normal function
of the tool. Do not attempt to prevent the recoil
by holding the nailer against the work. Restriction
to the recoil can result in a second fastener being
driven from the nailer. Failure to heed this warning
can result in serious personal injury.
DRY-FIRE LOCKOUT
When the magazine has 0-5 nails remaining, the dry-fire
lockout feature will not allow continued operation.
To resume operation, reload the tool with nails.
).
10 - English
LED WORKLIGHT
See Figure 10, page 15.
 To turn on the LEDs, press LED worklight grip switch
while firmly holding tool during operation.
DIAGNOSTIC FEEDBACK
The LED Worklight provides feedback to indicate whether
the battery pack is charged sufficiently and/or if the tool is
functioning properly.
If worklight is flashing, install fully charged battery. If light
continues to flash, see Troubleshooting section for more
information.
If the LED light goes out on your nailer, the unit has timed
out for your protection. Lift tool from the workpiece and
release trigger to activate the nailer before beginning next
drive cycle.
REMOVING NAILS FROM THE TOOL
See Figure 11, page 15.
WARNING:
Remove the battery pack before removing nails
or clearing a jammed nail. Failure to do so could
result in serious personal injury.
 Remove battery pack from the tool.
 To remove a strip of nails from the tool, depress the
magazine release button located at the rear of the
magazine and slide the magazine open.
 Remove nails.
 Close the magazine.
CLEARING A JAMMED FASTENER
See Figure 12 - 13, page 15.
WARNING:
Remove the battery pack from the tool before
clearing a jammed fastener. Failure to do so could
result in serious personal injury.
Driving too deeply into the material, excess debris, or
jammed nails may lead to the driver mechanism being stuck
at its bottom position.
The driver mechanism can usually be returned to its
operating position by depressing the workpiece contact
against a scrap piece of wood and squeezing the trigger.
If this does not automatically return the driver mechanism
into the tool, the tool may be jammed.
If a nail or fastener becomes jammed in the tool, remove
the battery pack and keep the tool pointed away from you
while clearing the jam.
 Remove battery pack from the tool.
 Remove fasteners from the tool.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

R09890vn

Tabla de contenido