Publicidad
Idiomas disponibles
Idiomas disponibles
Teflon
tape
1. All of the refrigerator installation
requirements must be met when
installing the filter.
Attach Fittings to Filter
2. a. Remove yellow endcaps from filter.
b. Apply 1 to 2 wraps of the included
Teflon tape to threads of o-ring
fittings, as shown.
c. Thread o-ring fittings into both ends
of the filter body and tighten snug with
a wrench. Leave at least one turn of
thread showing.
Cut Tubing
3. Shut off water supply.
4. The filter is to be inserted (spliced) into
the 1/4" OD supply tube that feeds
water to the refrigerator. (Do not cut any
water lines internal to the refrigerator.)
Locate the filter as close as possible to
the supply water shut-off valve. If the
filter needs to be located behind the
refrigerator, there needs to be at least 6
inches of clearance. If the appliance
1. Get a bucket and a towel.
2. Disconnect the old filter at its inlet first
and then its outlet. Water source will shut
off automatically, but some water may
spill or drip back through the filter.
3. Attach fittings to both ends of the new
filter body.
a. Find fittings that mate with filter body.
• What does this warranty cover?
— Any defect in materials or workmanship in the
manufactured product.
• What does this warranty not cover?
— Customer installation. The Installation Instructions cover installation
and replacement instructions.
— Defects that result from abuse, misuse, alterations, improper installation
or damage not caused by GE.
— Liability on the part of GE under this or any other warranty for any
indirect or consequential damage.
— Products that are used for commercial or industrial applications.
All manuals and user guides at all-guides.com
SUPPLY SIDE
Brass nut
Brass insert (for plastic tubing)
Valved fitting
Water line
Ferrule
tubing
Follow Directions for Proper Assembly
INSTALLING THE FILTER
must be moved, make sure there is
proper protection on the floor.
5. Cut the tubing, making sure the ends
are square and no burrs protrude.
Deburr ends with file or sandpaper
if necessary.
Attach Fittings to Tubing
6. Slip brass nuts then ferrules over both
tubing ends, leaving 1/4" of tubing
exposed from end. (See figure for
ferrule orientation). If your tubing is
plastic, place brass inserts into ends
of tubing.
7. a. Insert end of supply side tubing
into the valved fitting (the longer
fitting); hand-tighten nut onto
threads of fitting.
CAUTION: Be careful not to cross thread
the nut and the fitting.
b. Using two wrenches, tighten nut at
least one full turn.
c. Valved fitting is now installed. Turn
water supply on and inspect for leaks.
PROCEDURE FOR REPLACING THE FILTER
b. Apply one to two wraps of Teflon tape
to threads of o-ring fittings, as shown.
c. Thread o-ring fittings into filter body
and tighten snugly.
4. Place filter outlet over bucket; fine
particles of carbon may be present— flush
by connecting filter inlet to valved fitting.
Fine carbon particles will be removed
during the flushing. Disconnect inlet to
LIMITED 60 DAY WARRANTY
INLET OUTLET
O-ring
fitting
• For how long after the original purchase?
— Sixty (60) days.
• How do I make a warranty claim?
— Return to the retailer from which it was purchased along with a copy of
the "Proof of Purchase."
• How does state law relate to this warranty?
— This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
2
APPLIANCE SIDE
Brass insert (for
plastic tubing)
O-ring
Non-valved
fitting
fitting
d. Repeat a and b for non-valved fitting
on the appliance side.
Flush Filter
8. Place filter outlet over bucket; fine
particles of carbon may be present— flush
by connecting filter inlet to valved fitting.
Fine carbon particles will be removed
during the flushing. Disconnect inlet to
stop flushing after 2 to 3 gallons of water
are flushed (approx. 5 minutes).
Final Connection and Leak Check
9. Connect the outlet of the filter to the
water line going to your refrigerator.
10. Connect the inlet of the filter to the water
supply line and inspect for leaks. If a leak
occurs, tighten nuts or fittings until the
leak stops.
11. Write the date on the filter and also
mark your calendar to replace with
another filter after six months.
stop flushing after 2 to 3 gallons of water
are flushed (approx. 5 minutes).
5. Connect the filter outlet first, then
reconnect the inlet.
6. Write the date on the filter and also mark
your calendar to replace with another
filter after six months.
Brass nut
Ferrule
Water line
tubing
Publicidad
