Technical Data; Noise/Vibration Information; Declaration Of Conformity - Bosch GST 75 E Professional Instrucciones De Servicio

18
| English

Technical Data

Technical Data
Jigsaw
Article number
Rated power input
Stroke rate at no load n
º
Stroke
Cutting capacity, max.
– in Wood
– in aluminium
– in non-alloy steel
Bevel cuts (left/right), max.
Weight according to EPTA – Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] 127/220 V. These values can vary in case of lower voltage and models specific countries.
Observe the article number on the type plate of your power tool. The trade names of individual power tools may vary.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted noise levels of the product are:
Sound pressure level 88 dB(A); Sound power level 99 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting wood: ah=8.6m/s
Cutting sheet metal: ah=9.5m/s
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for
different applications, with different accessories or insertion
tools or is poorly maintained, the vibration emission may
differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched off
or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work
patterns.

Declaration of Conformity

We declare under our sole responsibility that the product
described under "Technical Data" is in conformity with all
relevant provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC including their amendments
and complies with the following standards:
EN 60745-1, EN 60745-2-11.
1 600 A00 5H4 | 2014.08
Manual GST 75 E Professional.indd 18
2
, K=1.5m/s ,
2 , K=1.5m/s 2 .
W
min
-1
mm
mm
mm
mm
°
Kg
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen
GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
22.12.2014
Assembly
u Before any work on the machine itself, pull the mains
plug.
Replacing/Inserting the Saw Blade
u When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
Selecting a Saw Blade
An overview of recommended saw blades can be found at
the end of these instructions. Use only T-shank saw blades.
The saw blade should not be longer than required for the
intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A1)
Insert the saw blade 8 (teeth in cutting direction) into the
stroke rod 11 until it latches. The SDS lever 12 automatically
snaps to the rear and the saw blade is locked. Do not
manually press the lever 12 toward the rear, otherwise you
could damage the machine.
While inserting the saw blade, pay attention that the back of
the saw blade is positioned in the groove of the guide roller 7.
u Check the tight seating of the saw blade. A loose saw
blade can fall out and lead to injuries.
GST 75 E
3 601 E8H...
710
800–3100
20
75
20
10
45
2.5
/II
Bosch Power Tools
20/02/15 15:04