Publicidad
Idiomas disponibles
Idiomas disponibles
H-4091, H-4092
WORKSTATION FANS
TOOLS NEEDED
Phillips
3/4" Socket Wrench
Screwdriver
Fan Head x 1
1/2" Bolt x 1
For Steel Structures
(not included)
CAUTION! It is important that the following
safety precautions be followed when using
this product:
• Always unplug unit for cleaning or maintenance.
• Always unplug unit when not in use.
• Always unplug when moving unit from one location
to another.
• Do not use an extension cord. Plug fan into a
properly-rated electrical outlet.
• Do not place foreign objects through guards into
blades.
• Do not allow unit to become wet or damp.
• Do not use this fan with any solid-state speed
control device.
• Do not operate any fan with a damaged cord or
plug. Discard fan or return to an authorized service
facility for examination and/or repair.
PAGE 1 OF 6
1-800-295-5510
uline.com
PARTS
1/2" Lag Screw x 1
For Wood and Masonry Structures
(not included)
Flat Washer x 2
(not included)
SAFETY
• Do not run cord under carpeting.
• Do not cover cord with throw rugs, runners or similar
• Do not route cord under furniture or appliances.
Pour le français, consulter les pages 5-6.
Lock Washer x 1
For Steel Structures
(not included)
coverings.
Arrange cord away from traffic areas and where it
will not be tripped over.
WARNING! To reduce risk of fire, electric shock
or injury to people, observe the following:
• Use this unit only in the manner intended
by the manufacturer. If user has questions,
contact Uline Customer Service at
1-800-295-5510.
• Before servicing or cleaning unit, switch
power off at service panel and lock
service panel to prevent power from being
switched on accidentally. When the service
panel cannot be locked, securely fasten a
prominent warning device, such as a tag,
to it.
Para Español, vea páginas 3-4.
Lag Shield x 1
For Masonry Structures
(not included)
1/2" Nut x 1
For Steel Structures
(not included)
1021 IH-4091
Publicidad
Tabla de contenido
Manuales relacionados para Uline H-4091
Resumen de contenidos para Uline H-4091
- Página 1 • Use this unit only in the manner intended by the manufacturer. If user has questions, • Do not place foreign objects through guards into contact Uline Customer Service at blades. 1-800-295-5510. • Do not allow unit to become wet or damp.
- Página 2 If bearing lubrication is required, apply a small bearing. Replace front guard in reverse order of amount of synthetic oil to the motor bearing. disassembly. Allow fan to dry completely before next use. 1-800-295-5510 uline.com PAGE 2 OF 6 1021 IH-4091...
-
Página 3: Ventiladores Para Estación De Trabajo
Si el usuario tiene alguna duda, comuníquese con Servicio a Clientes • No coloque objetos extraños en las aspas a través de Uline al 800-295-5510. de los protectores. • Antes de dar mantenimiento o limpiar • No permita que la unidad se moje o humedezca. -
Página 4: Instalación
Reemplace el protector frontal en el orden inverso del desensamble. Permita que el ventilador se seque por completo antes del próximo uso. 800-295-5510 uline.mx PAGE 4 OF 6 1021 IH-4091... -
Página 5: Outils Requis
Pour toutes questions, contactez le • Ne placez pas d'objets étrangers dans les pales à service à la clientèle de Uline au travers les protecteurs. 1 800 295-5510. • L'appareil ne doit être ni humide ni mouillé. - Página 6 Remettez synthétique sur le roulement du moteur. en place la grille à l’avant en suivant l’ordre inverse du démontage. Faites sécher complètement le ventilateur avant de le réutiliser. 1-800-295-5510 uline.ca PAGE 6 OF 6 1021 IH-4091...