Denon ADV-700 Instrucciones De Operación página 15

[2] Setting the speaker distance
• Input the distances from the listening position to the
speakers and set the surround delay time.
• The default settings below are set upon shipment from the
factory.
Preparations:
Measure the distances from the listening position to the
speakers (L1 to L3 on the diagram at the right).
L1: Distance from center speaker to
FL Center FR
listening position
L2: Distance from front speakers to
listening position
L
L L3: Distance from surround speaker
1
2
Listening
to listening position
position
L
3
SL SR
1 To perform these operations from places other than the
system setting change menu, see page 14.
2 At the SYSTEM SETUP MENU select "DELAY TIME".
ENTER
\
Remote control unit Remote control unit
• Switch to the DELAY TIME screen.
B
DELAY TIME
S E T T H E D I S T A N C E T O E A C H S P E A K E R S S E T T H E D I S T A N C E T O E A C H S P E A K E R S
U N I T U N I T METERS F E E T METERS F E E T
DEFAULT DEFAULT
FRONT&SW FRONT&SW 2 . 7 m
CENTER CENTER 2 . 4 m
SURROUND SURROUND 2 . 1 m
SELECT : FINISH: ENTER BUTTON
• Use the and cursor buttons to select the distance
unit, "METERS" or "FEET".
Press the cursor button to proceed to the next step if
you do not wish to change this.
3 When "YES" is selected for "DEFAULT", the delay
times for the various speakers are set to the default
values.
FRONT & SW / 2.7 m
B YES:
CENTER / 2.4 m
SURROUND / 2.1 m
B NO: The current settings are used.
All manuals and user guides at all-guides.com
4
Select the speaker to be set using the and
cursor buttons, then setting the distance between the
speakers and the listening position using the and
cursor buttons.
• Set the distance between the center speaker and listening
position.
The distance changes in units of 0.1 meters (1 foot) each
time the button is pressed. Select the value closest to the
measured distance.
DELAY TIME B
S E T T H E D I S T A N C E T O E A C H S P E A K E R S S E T T H E D I S T A N C E T O E A C H S P E A K E R S
U N I T U N I T METERS METERS F E E T
DEFAULT DEFAULT
FRONT&SW FRONT&SW 2 . 7 m
CENTER CENTER 2 . 4 m
SURROUND SURROUND 2 . 1 m
SELECT : FINISH: ENTER BUTTON
The difference of the distances set for the different speakers
must be no greater than 3.0 m (10 ft.).
If an inapplicable distance is set, "CAUTION: INVALID
DISTANCE" is displayed. Change the speaker position and
reset.
5 Enter the setting.
ENTER
• The SYSTEM SETUP MENU
reappears.
Remote control unit
[3] Setting the channel level
• Use this setting to adjust so that the playback level between
the different channels is equal.
• From the listening position, listen to the test tones produced
from the speakers to adjust the level.
• The level can also be adjusted directly from the remote
control unit. (For details, see page 22.)
1 To perform these operations from places other than the
system setting change menu, see page 14.
2 At the SYSTEM SETUP MENU select "CHANNEL
LEVEL".
ENTER
\
Remote control unit Remote control unit
• Switch to the CHANNEL LEVEL screen.
B
C H A N N E L L E V E L
TEST TONE MODE TEST TONE MODE AUTO MANUAL MANUAL
L E V E L C L E A R L E V E L C L E A R
T E S T T O N E S T A R T T E S T T O N E S T A R T
F R O N T L 0 d B
CENTER 0 d B
F R O N T R 0 d B
SURROUND R 0 d B
SURROUND L 0 d B
SUBWOOFER SUBWOOFER 0 d B
SELECT : FINISH: ENTER BUTTON
3 Select "TEST TONE MODE".
• Select the mode.
Remote control unit
Select "AUTO" or "MANUAL".
• AUTO: Adjust the level while listening to the test tones
produced automatically from the different speakers.
• MANUAL: Select the speaker from which you want to
produce the test tone to adjust the level.
4 If "YES" is selected at "LEVEL CLEAR", the level
settings for all the speakers are set to 0 dB.
B "YES" : The levels of the different speakers are all set to
0dB.
B "NO" : The speakers stay at their currently set levels.
5 Adjusting the channel levels in the "test tone" mode
• Set the "TEST TONE START" mode using the
and cursor buttons, then select "YES" with the
cursor button to output test tones.
ENGLISH
6 q When "AUTO" is selected in the "TEST TONE
MODE"
B
C H A N N E L L E V E L
TEST TONE MODE TEST TONE MODE AUTO MANUAL MANUAL
L E V E L C L E A R
T E S T T O N E S T A R T Y E S
+ 1 0 d B
F R O N T L
CENTER 0 d B
F R O N T R 0 d B
SURROUND R SURROUND R 0 d B
SURROUND L SURROUND L 0 d B
SUBWOOFER SUBWOOFER 0 d B
SELECT : FINISH: ENTER BUTTON
• Test tones are automatically emitted from the different
speakers.
• The test tones are emitted from the different speakers in
the following order, at 4-second intervals the first time and
second time around, 2-second intervals the third time
around and on:
FRONT L FRONT R
CENTER
SUBWOOFER SURROUND L SURROUND R
• Use the CURSOR buttons to adjust all the speakers to the same
volume.
• The volume can be adjusted between –12 dB and +12 dB in units
of 1 dB.
w When the "MANUAL" mode is selected
C H A N N E L L E V E L B
TEST TONE MODE TEST TONE MODE AUTO MANUAL MANUAL
L E V E L C L E A R
T E S T T O N E S T A R T Y E S
F R O N T L + 1 0 d B
CENTER 0 d B
F R O N T R 0 d B
SURROUND R SURROUND R 0 d B
SURROUND L SURROUND L 0 d B
SUBWOOFER SUBWOOFER 0 d B
SELECT : FINISH: ENTER BUTTON
• Use the CURSOR and to select the speaker for
which you want to output test tones, then use the CURSOR
and to adjust so that the volume of the test tones
from the various speakers is the same.
15