Black and Decker SSL16 Manual De Instrucciones página 5

90565382 SSL16 SSL20 NEW Smart Select.qxd:??????-00 BDL500 laser
pack after use, avoid placing the charger or battery pack in a warm environment such as
in a metal shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or other appliance
b. Check to see if receptacle is connected to a light switch which turns power off
when you turn out the lights.
c. Move charger and battery pack to a location where the surrounding air
temperature is approximately 65°F - 75°F (18°- 24°C).
d. If charging problems persist, take the tool, battery pack and charger to your
local service center.
4. The battery pack should be recharged when it fails to produce sufficient power on
jobs which were easily done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also charge a partially used pack
whenever you desire with no adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply when there is no battery
pack in the cavity. Unplug charger before attempting to clean.
6. Do not freeze or immerse charger in water or any other liquid.
WARNING:
Shock hazard. Do not allow any liquid to get inside charger. Never
attempt to open the battery pack for any reason. If the plastic housing of the battery pack
breaks or cracks, return to a service center for recycling.
SAFETY WARNINGS AND INSTRUCTIONS: DRILLS
1. Hold drill firmly with one hand on the grip and the other hand on the bottom of the
battery pack.
2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.
WARNING:
Drill may stall (if overloaded or improperly used) causing a twist.
Always
expect the stall. Grip the drill firmly with both hands to control the twisting action and
prevent loss of control which could cause
personal injury. If a stall does occur, release
the trigger immediately and determine the
reason for the stall before re-starting.
INSTALLING AND REMOVING THE
BATTERY PACK FROM THE TOOL
WARNING:
Make certain the lock-off
button is engaged to prevent switch actuation
before removing or installing battery.
TO INSTALL BATTERY PACK: Insert battery
pack into tool until an audible click is heard
as shown in figure B.
TO REMOVE BATTERY PACK: Depress the
battery release button as shown in figure C
and pull battery pack out of tool.
All manuals and user guides at all-guides.com
B
C
8
6/3/10 1:40 PM Page 8
OPERATING INSTRUCTIONS
TRIGGER SWITCH & REVERSING BUTTON (FIGURE D)
• The drill is turned ON and OFF by pulling
and releasing the trigger switch (1). The
farther the trigger is depressed, the higher
the speed of the drill.
• A forward/reverse control button (2)
determines the toolʼs direction and also
serves as a lock off button.
• To select forward rotation, release the
trigger switch and depress the
forward/reverse control button to the left.
• To select reverse, depress the
forward/reverse control button the opposite
direction.
NOTE: The center position of the control
button locks the tool in the off position.
When changing the position of the control
button, be sure the trigger is released.
TORQUE CONTROL (SMART SELECT TECHNOLOGY) (FIGURE E)
This tool is fitted with a collar (3) which depicts various drilling and screwdriving
applications. They are used to select the operating mode and to set the torque for
tightening screws. Large screws and hard workpiece materials require a higher torque
setting than small screws and soft workpiece materials.
When the optimal performance selector collar (3) is rotated to any of the images shown in
the chart below, the tool shifts to deliver either the recommended torque or speed for that
application.
E
3
ON-PRODUCT
IMAGE
D
2
1
APPLICATION
DRILL AUTOMATICALLY DELIVERS
Driving 1/4 in.-1 in. screws
LOW TORQUE
Driving 1 in. or longer screws
MEDIUM TORQUE
Drilling 5/16-1/2 in. into metal HIGH TORQUE
HIGHEST TORQUE
Driving 1 in. or larger spade bit
Transition from
SHIFT
HIGH TORQUE to HIGH SPEED
Drilling up to 1/2 in. drill bit
HIGH SPEED
into any material
Drilling 1/8 in.-1/4 in. into metal HIGH SPEED
Driving 7/8 in.-1 in. spade or
HIGH SPEED
smaller bit into wood
9