Picture-In-Picture (Pip) Operation; Basic Pip Operation - Sanyo DS27820 Manual Del Propietário

PICTURE-IN-PICTURE (PIP) OPERATION

QuickTips
PIP window is black
I
with no picture:
1. Check cable or
antenna connections.
2. Make sure VCR is
turned on.
3. Select another channel
on your VCR.
Same picture appears
I
in Big and Small
windows. Set VCR
to TV mode.
P P I I P P K K E E Y Y S S : :
Use the S S W W A A P P key to
I
exchange programs
between the windows.
Use the L L O O C C A A T T I I O O N N
I
key to change the
position of the small
window (Top: L/R or
Bottom: L/R).
Use the Q Q U U I I K K
I
F F R R E E E E Z Z E E key to
stop the action. Use
this feature to hold an
advertised phone
number or address
on the screen until
you collects the
information.
Use the S S E E L L E E C C T T
I
key to choose the PIP
video source (Video1
or Video2, or TV RF
signal).
N N e e e e d d h h e e l l p p ? ?
V V i i s s i i t t o o u u r r W W e e b b s s i i t t e e a a t t
www.sanyoctv.com
o o r r C C a a l l l l 1 1 - - 8 8 0 0 0 0 - - 8 8 7 7 7 7 - - 5 5 0 0 3 3 2 2
1 1 4 4
For PIP to function you must connect two signals to the TV.
input and AV inputs.) Connect VCR (or other accessory equipped with a video output jack) to
the TV's audio video jacks as shown at the right and on page 15 or 16. If you are using a satel-
lite dish, you must connect a cable system or antenna also to use the PIP feature (see page 15).
For operation with Cable Box, see connection on page 16.

BASIC PIP OPERATION

(Connect signal first.)
Note: The following steps correspond to numbers
on the Remote Control art below.
‚
Switch TV and VCR ON.
ƒ
Press the PIP ON/OFF key. Set VCR to TV mode,
if necessary.
„ ‡
or Select channel for big window.
…
Press the SELECT key to choose Video1 or Video2 signal.
†
Press the VCR key.
Note: If the remote control cannot be programmed to
operate your VCR, you must use the VCR's
remote to perform VCR functions.
‡ „
or Select channel on VCR for PIP (small) window.
ˆ
To change the position of the PIP window, press
the LOCATION key.
Notes:
The PIP channel number will always appear in the
–
upper left hand corner regardless of the PIP window
location.
– PIP cannot be used with
the component input jacks.
Switching to component
input with PIP active will
automatically switch PIP
off.
‰
Press the SWAP key to
view PIP image in big
window.
BASIC PIP CONNECTION
W W h h a a t t y y o o u u w w i i l l l l n n e e e e d d f f o o r r c c o o n n n n e e c c t t i i o o n n s s : :
A A V V C C a a b b l l e e – – 1 1
R R F F C C a a b b l l e e – – 1 1
O O R R
PIP
Window
Big
Window
†
‚
‡
„
ƒ
‰
(Use the TV's 75 ohm
V V C C R R B B a a c c k k
T T V V B B a a c c k k
ˆ …