Care & Maintenance - Ninja CREAMi NC300 Serie Guia Del Usuario

USING THE CREAMi® – CONTINUED
11a If adding mix-ins, use a spoon to
MIX-IN TIPS
We recommend adding /
1
4
frozen fruits, chopped nuts, chocolate pieces, and more. When
adding several different types of mix-ins, we recommend not
exceeding / cup in total. Feel free to adjust the quantity of
1
4
mix-ins to your taste but make sure that the outer bowl lid can
still comfortably close over the pint.
Hard mix-ins will remain intact. Mix-ins like chocolate, candy,
and nuts will not be broken down during the MIX-IN program.
We recommend using mini chocolate chips and candies or
pre-chopped ingredients.
Soft mix-ins will get broken down. Mix-ins like cereal, cookies,
and frozen fruit will end up smaller after the MIX-IN program.
We recommend using bigger pieces of soft ingredients.
For ice cream and gelato, we do not recommend fresh fruit, sauces,
and spreads as mix-ins. Adding fresh fruit, fudge, and caramel sauces
will water down your treat. Chocolate hazelnut spread and nut butters
also do not mix well. We recommend using frozen fruit or chocolate/
caramel shell toppings.
11b If not adding mix-ins, RE-SPIN can be
NOTE: Do not RE-SPIN before using the MIX-IN program.
12 Lift the pint out of the outer bowl.
13 Rinse the outer bowl lid to remove any
14 Turn the unit off by pressing the
15 Didn't finish your pint? Flatten the
NOTE: Leftovers can be stored in other containers. However,
we recommend storing leftovers in a pint so that it can be
processed again if necessary.
NOTE: If your treat contains mix-ins, processing again will
further crush your mix-ins and create a new flavor.
create a 1 / -inch wide hole that
1
2
reaches the bottom of the pint. Add
chopped or broken mix-ins to the
hole in the pint and repeat steps
6-10 to process again using the
MIX-IN program.
cup of your favorite crushed candies,
used on a crumbly or powdery pint to
make it more creamy. RE-SPIN is often
needed for very cold bases. If the treat
is smooth and scoopable, go to step
12. If the base is crumbly or powdery,
repeat steps 6–10 to process again
using the RE-SPIN program.
Enjoy your treat!
sticky residue or pieces wedged in
the Creamerizer Paddle. Then detach
the paddle by pressing the latch on
the top of the outer bowl lid. For easy
cleanup, release paddle directly into
the sink.
power button. Unplug the unit
when finished. Refer to the Care &
Maintenance section for cleaning
and storage instructions.
top of your frozen treat with a spoon or
spatula before refreezing. If the treat is
hard after re-freezing, process it again
on the program you used to make it.
If it's soft, just scoop and enjoy it.
CARE & MAINTENANCE
CLEANING
NOTE: Before cleaning, make sure to remove the Creamerizer™
Paddle from the outer bowl lid by rinsing the lid and then
pressing the paddle latch.
Hand-Washing
Wash containers, lids, and paddle in warm, soapy water. Use a
dishwashing utensil with a handle to clean the paddle. Thoroughly
rinse and air-dry all parts.
Dishwasher
Containers, lids, and paddle are dishwasher safe (top rack only).
Ensure the paddle, pint, outer bowl, and lids are all separated before
placing them in the dishwasher.
NOTE: For best results, use a dishwasher to remove stuck-on
ingredients.
Outer Bowl Lid
Remove the paddle before cleaning the outer bowl lid as ingredients
may be stuck under the paddle. Then run warm water through the
paddle release lever and out the drain holes on either side. Position
the lid with the lever side down to fully drain the lid.
Remove the dark grey rubber lip seal wrapped around the middle of
the underside of the outer bowl lid. Then hand wash the lid and seal
with warm, soapy water or place in the dishwasher.
Motor Base
STORING
For cord storage, wrap the cord with the hook-and-loop fastener
near the back of the motor base. DO NOT wrap the cord around the
bottom of the base for storage.
Do store any remaining attachments alongside the unit or in a
cabinet where they will not be damaged or create a hazard.
RESETTING THE MOTOR
This unit features a unique safety system that prevents damage to
the motor and drive system should you inadvertently overload it.
If the unit is overloaded, the motor will be temporarily disabled.
Should this occur, follow the reset procedure below.
1 Unplug the unit from the electrical outlet.
2 Allow the unit to cool for approximately 15 minutes.
3 Remove the outer bowl lid and paddle. Ensure no ingredients
are jamming the lid assembly.
IMPORTANT: Ensure that maximum capacities are not exceeded.
This is the most typical cause of appliance overload.
DO NOT process a solid block of ice or ice cubes. DO NOT make
a smoothie or process hard, loose ingredients. Fruit must be crushed
to release its juice or combined with other ingredients and frozen
before processing.
If your unit needs servicing, please call Customer Service at
1-877-646-5288. So we may better assist you, please register your
product online at registeryourninja.com and have the product on
hand when you call.
Unplug the motor base before cleaning.
Wipe motor base with a clean, damp
cloth. Do not use abrasive cloths, pads,
or brushes to clean the base.
Using a damp cloth, wipe the spindle
below the control panel after each use.
If liquid is trapped between the motor
base and the platform, raise the platform
to clean.
Place the outer bowl onto the motor
base with the handle centered below
the control panel.
Twist the handle to the right to raise
the platform.
Then use a damp cloth to clean the area
between the base and the raised platform.