Haier HSM07HEK03/R2 Manual De Instalación
Ocultar thumbs Ver también para HSM07HEK03/R2:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Installation Manual of Room Air Conditioner
Preparation
Necessary Tools for Installation
Driver
Nipper
Hacksaw
Hole core drill
Spanner(17,19 and 26mm)
Gas leakage detector or
soap-and-water solution
Power Source
Before inserting power plug into receptacle, check the voltage without fail.
The power source is the same as the corresponding name plate.
Install an exclusive branch circuit of the power.
A receptacle shall be set up in a distance where the power cable can be
reached.Do not extend the cable by cutting it.
Drawing for the installation of indoor and outdoor units
The models adopt HFC free refrigerant R410A
more than 5cm
more than
10cm
Arrangement of piping
directions
Rear left
Rear
Left
right
Right
Below
more than 10cm
The marks from
to
A
in the figure are the
G
parts numbers.
The distance between
the indoor unit and the
floor should be more
than 2m.
more than 60cm
Please be subject to the actual product purchased , the above picture is just for your reference.
Read this manual before installation
Explain sufficiently the operating means to the user according to this manual
NO.0010531115
All manuals and user guides at all-guides.com
Torque wrench
(17mm,22mm,26mm)
Pipe cutter
Flaring tool
Knife
Measuring tape
Reamer
Attention must be paid to
the rising up of drain hose
more than 10cm
more than
10cm
Selection of Installation Place
Indoor Unit
Place, robust not causing vibration, where the body can be supported sufficiently.
Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the
unit are not disturbed.
Place, possible to drain easily, where piping can be connected with the outdoor unit.
Place, where cold air can be spread in a room entirely.
Place, nearby a power receptacle, with enough space around. (Refer to drawings).
Place where the distance of more than lm from televisions, radios, wireless apparatuses
and fluorescent lamps can be left.
In the case of fixing the remote controller on a wall, place where the indoor unit can
receive signals when the fluorescent lamps in the room are lightened.
Outdoor Unit
Place, which is less affected by rain or direct sunlight and is sufficiently ventilated.
Place, possible to bear the unit, where vibration and noise are not increased.
Place, where discharged wind and noise do not cause a nuisance to the neighbors.
Place, where a distance marked
G
F
Floor fixing dimensions of the
A
outdoor unit (Unit:mm)
C
Fixing of outdoor unit
D
E
more than15cm
is available as illustrated in the above figure.
Optional parts for piping
Non-adhesive tape
A
Adhesive tape
B
Saddle (L.S) with screws
C
Connecting electric cable
D
for indoor and outdoor
E
Drain hose
F
Heating insulating material
Piping hole cover
G
Fix the unit to concrete or block
with bolts (10mm) and nuts firmly
and horizontally.
When fitting the unit to wall
surface, roof or rooftop, fix
a supporter surely with nails
or wires in consideration of
earthquake and strong wind.
If vibration may affect the
house, fix the unit by attaching a
vibration-proof mat.

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Haier HSM07HEK03/R2

  • Página 1 All manuals and user guides at all-guides.com Installation Manual of Room Air Conditioner Preparation Selection of Installation Place Necessary Tools for Installation Torque wrench Indoor Unit Driver (17mm,22mm,26mm) Nipper Place, robust not causing vibration, where the body can be supported sufficiently. Hacksaw Pipe cutter Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the...
  • Página 2: Indoor Unit

    All manuals and user guides at all-guides.com 1. Insert the drain hose into the dent of heat insulation materials of indoor unit. Accessory parts 2. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it out on the front side, then connect them. 3.
  • Página 3: Installation Of Outdoor Unit

    30 to 40 mm or longer. Connecting the pipe of gas side first makes working easier. The connection pipe is specialized for R410A. HUM07HA03/R2(DB) HSM07HEK03/R2(DB) HUM09HA03/R2(DB) HSM09HEK03/R2(DB) Forced fastening without careful centering may Half union...
  • Página 4 All manuals and user guides at all-guides.com 1.Cut pipe 2.Remove burs Flare tooling die Attaching Drain-Elbow If the drain-elbow is used, please attach it as figure. (Note: Only for heat pump unit.) 3.Insert the flare nut 4.Flare pipe Purging Method:To use vacuum pump Detach the service port’s cap of 3-way valve, the valve rod’s cap for 2-way valve and 3-way’s, connect the service port into the projection of charge hose (Iow)
  • Página 5: Preparación

    All manuals and user guides at all-guides.com Manual de instalación de aparato de aire acondicionado Preparación Herramientas necesarias para realizar la instalación Selección del lugar de instalación Unidad interior Destornillador Llave dinamométrica (17 mm, 22 mm, 26 mm) ● Coloque la unidad sobre una superficie que pueda soportarla correctamente y no Alicate provoque vibraciones.
  • Página 6: Unidad Interior

    All manuals and user guides at all-guides.com [Izquierda • Entubación trasera izquierda] Accesorios En caso de realizar la entubación por el lado izquierdo, corte con una cuchilla la cubierta de la entubación izquierda. En caso de realizar la entubación a través de la parte trasera izquierda, doble los Control remoto (1) Manguera de drenaje (1) tubos de acuerdo con la dirección de entubación que figura en la marca del orificio...
  • Página 7: Unidad Exterior

    3G1.5mm por un ingeniero profesional en aire acondicionado. Antes de añadir refrigerante adicional, realice una purga de aire desde los tubos refrigerantes y la unidad interior HSM07HEK03/R2(DB) HUM07HA03/R2(DB) utilizando una bomba de vacío y cargue después el refrigerante adicional. HSM09HEK03/R2(DB)
  • Página 8: Etiqueta De Carga De Refrigerante

    All manuals and user guides at all-guides.com 1. Retire el tapón del puerto de mantenimiento de la válvula de 3 vías, el tapón del ● Después de insertar la tuerca cónica deberá procederse a realizar los trabajos de vástago de la válvula de 2 vías y 3 vías, y conecte el puerto de mantenimiento a conicidad.
  • Página 9 All manuals and user guides at all-guides.com Manuale d’installazione del Condizionatore Preparazione Attrezzi necessari per l’’installazione Selezione del luogo d’installazione Unità interna Cacciavite Chiave dinamometrica (17mm, 22mm, 26mm) ● Installare in un luogo solido, senza vibrazioni, in grado di supportare il peso dell’ Pinza unità.
  • Página 10: Unità Interna

    All manuals and user guides at all-guides.com Se la tubatura è posteriore sinistra, piegare i tubi seguendo la direzione delle tuba- Parti accessorie ture verso il contrassegno del foro per la tubatura sinistra posteriore che è stampi- gliato sui materiali d'isolamento termico. 1.
  • Página 11 20 g/m. Tuttavia, il caricamento del refrigerante deve essere eseguito da Cavo d’alimentazione: 3G1.5mm personale professionista. Prima di aggiungere altro refrigerante, eseguire lo sfiato dell’ HSM07HEK03/R2(DB) HUM07HA03/R2(DB) aria dalle tubature del refrigerante e dall’unità interna usando una pompa a vuoto, poi caricare il refrigerante.
  • Página 12 All manuals and user guides at all-guides.com 3. Aspirare per oltre 15 minuti. Controllare l'indicatore che deve indicare -0.1MPa (76 cm Profilo attrezzo per svasatura 1. Tagliare il tubo Hg) sul lato della bassa pressione. Dopo avere completato la procedura di scarico, 2.
  • Página 13 All manuals and user guides at all-guides.com Manuel d'installation d'un climatiseur de pièce Préparation Outillage requis pour l'installation Sélection de l'emplacement pour l'installation Unité intérieure Clé Clé dynamométrique (17 mm, 22 mm, 26 mm) ● L'emplacement doit être solide sans vibration et offrir un support suffisant. Pince ●...
  • Página 14: Unité Intérieure

    All manuals and user guides at all-guides.com [Gauche • Tuyauterie arrière gauche] Accessoires Dans le cas d'une tuyauterie à gauche, découpez, avec une pince, le couvercle pour la tuyauterie gauche. Pour une tuyauterie à l'arrière gauche, cintrez les tuyaux selon le sens de la tuyau- Télécommande (1) Tuyau de vidange (1) terie jusqu'à...
  • Página 15: Unité Extérieure

    Toutefois, la charge de réfrigérant doit être exécuté par un professionnel de la climati- sation. Avant d'ajouter du réfrigérant, purgez l'air des tuyaux de réfrigération et de l'unité HSM07HEK03/R2(DB) HUM07HA03/R2(DB) intérieure avec pompe à vide. Chargez ensuite le réfrigérant supplémentaire.
  • Página 16: Etiquette De Charge De Réfrigérant

    All manuals and user guides at all-guides.com 1. Enlevez le capuchon de l'orifice d'entretien de la vanne à 3 voies, le capuchon ● Après avoir inséré l'écrou évasé, vous pouvez procéder au travail d'évasement. du robinet de la vanne à 2 voies et à 3 voies. Connectez ensuite l'orifice d'entre- Outil d'évassement tien dans la projection du tuyau de charge (bas) pour le collecteur à...

Tabla de contenido