Campingaz Adelaide Utilización Y Mantenimiento página 7

Keep away from any parts of the barbecue that get hot.
Check that the flexible hose stretches out normally,
without twisting or pulling.
Switzerland, Germany, Austria:
The barbecue should be used with flexible tubing that is
suitable for use with butane and propane gas. Hose
length should not exceed 1.50 metre. It should be
replaced if it is damaged or develops surface cracks or
when so required by national legislation. Do not pull or
pierce the tubing. Keep away from any parts of the
barbecue that get hot. Check that the flexible hose
stretches out normally, without twisting or pulling.
Flexible tubing connection: to connect the tubing to the
connector on the barbecue, tighten the nut on the tubing
firmly but without excess force using the two wrenches
provided:
- no. 14 wrench to tighten the connector
- no. 17 wrench to tighten the nut on the tubing
e) LID (DEPENDING ON MODEL)
Handle the lid carefully, especially during operation. Do not
lean over the base.
f)CHECKING FOR GAS LEAKS
1) Work outside, away from all sources of ignition. Do not
smoke.
2) Make sure the control knobs are in the "off" ( ) position.
Connect the flexible tubing to the connector and
3)
barbecue as described in part d).
4) Fit the regulator onto the gas cylinder in accordance with
its instructions.
5) Use a gas leak solution to test for leaks.
use a naked flame to check for gas leaks.
6) Apply the solution to the connections cylinder/regulator/
hose/apparatus (the control knobs should remain closed:
off position ( )). Open the gas cylinder valve.
7) Bubbles in the gas leak solution indicate that there are gas
leaks.
8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. The
barbecue must not be used until the leak is stopped.
9) Close the valve on the gas cylinder.
All manuals and user guides at all-guides.com
Important:
Check for leaks at least once per year and each time the gas
cylinder is replaced.
g) PRIOR TO SE
Never use the barbecue until the instructions have been read
carefully and understood. Also, make certain that:
- there are no leaks
- the venturi tubes are not blocked (example: spider webs)
- the hose does not touch any components which may get
- that the ventilation openings in the gas receptacle housing
h) LIGHTING THE BARBEC E B RNERS
- Remove the protective cover or open the cooking area
- Make sure that the control knobs are in the "OFF"
- Push an adjustment button down and turn it anti-
- Repeat this operation until the burner lights.
- If the burner does not ignite after 4 or 5 attempts, wait 5
Once the burner is lit, there are two ways of lighting
another burner:
Important:
never
If the piezoelectric ignition does not function, light the burners
manually (next paragraph).
i) LIGHTING THE BARBEC E MAN ALLY
- Remove the protective cover or open the cooking area
- Make sure that the control knobs are in the "OFF"
- Remove the grease drip tray.
- Strike a match and bring it close to the burner from
- Push an adjustment button down and turn it anti-
- Once the burner is lit, place the grease drip
Once the burner is lit, there are two ways of lighting
another burner:
7
hot.
are not obstructed, if appropriate.
Check that the venturi tubes (VT) cover the
injectors (IJ).
lid (depending on model).
position ( ).
clockwise until it is in the full flow position ( ) , then
immediately press the ignition button down (
) until you hear a click. Repeat 3 or 4 times if necessary.
minutes and then repeat the operation.
rÿ
Firstly, repeat the lighting operation described above;
rÿ
Secondly, light the burner to the right or left of the first
burner lit, then the other burners in turn by turning the
adjustment button to the full flow position ( ) .
lid (depending on model).
position ( ).
below.
clockwise until it is in the full flow position ( ) .
tray back in position.
rÿ
Firstly, repeat the lighting operation described above;
r
Secondly, light the burner to the right or left of the first
burner lit, then the other burners in turn by turning the
adjustment button to the full flow position ( ) .
GB