OttLite X12478 Guia De Inicio Rapido

F
C
A
13w Craft Space Organizer Lamp
X12478 X12008 X12TU8 X12008-FFP
INS150157
b
D
GX-8269
English
CONGRATULATIONS!
You've purchased the finest in natural lighting technology with
your new OttLite ® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
www.warranty.ottlite.com
WARNING: To prevent electric shock, make sure the lamp is
not plugged in until all assembly steps are complete.
LAMP ASSEMBLY
1. Unpack all lamp parts and lay out with the base (A) lying flat
on a steady surface.
2. To install the shade (C), align the notch of the shade with
the tab of the socket housing then push it back into the
socket assembly making sure the shade snaps into place.
3. Install tube (F). See TUBE INSTALLATION/REMOVAL
instructions.
4. Plug the lamp into a standard 120V outlet.
5. Adjust the position of the shade (C) by grasping it near the
flex neck (B) and reposition.
6. Turn lamp ON or OFF by depressing switch (D).
TUBE INSTALLATION AND REMOVAL
1. Make sure that the lamp is not plugged into an electrical
socket.
2. If the lamp has been in use, allow it to cool approximately 5
minutes before proceeding.
3. Rotate the shade (C) so that the notch in the base of the
shade is positioned over the tab located on the socket
assembly.
4. Remove the shade (C) by pulling it straight out from the
socket assembly.
5. To install a tube (F) in the socket, grasp the tube firmly in
your hand, position the tube so that the pins are aligned with
the socket receptacle then push the tube straight into the
socket until it "snaps" into place.
6. To remove a tube (F) already installed in the lamp, grasp it
firmly at the base and, using a slight rocking motion, pull it
straight out of the socket. DO NOT twist or turn the glass
part of the tube. It is highly recommended to remove
shade prior to inserting tube.
7. To replace the shade (C), align the notch of the shade with
the tab of the socket housing then push it back into the
socket assembly making sure the shade "snaps" into place.
13w Craft Space Organizer Lamp
Please note that in operation, OttLite tubes are not dimmable.
Enjoy your 13w Craft Space Organizer Lamp!
This lighting system is designed for use with OttLite type
(style number PL13-E). Use of other products voids the
warranty and may result in damage to the lighting system.
For more information on purchasing replacement tubes/bulbs
please go to www.OttLite.com/replacement13wtube
CAUTION!
If the external flexible cable or cord of
this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or its service agent or a similar qualified person in
order to avoid a hazard. Indoor use only.
CAUTION!
To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
CAUTION! ImpOrTANT sAfeTy
INsTrUCTIONs:
This portable lamp has a polarized
plug (one blade is wider than the other) as a feature to reduce the
risk of electric shock. This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. Never use with an
extension cord unless plug can be fully inserted. Do not alter the plug.
This product complies with Part 18 of FCC Rules, but may cause
interference to radios, televisions, wireless telephones, and remote
controls. Avoid placing this product near these devices. If interference
occurs, move the product away from the device or plug either into
a different outlet. Do not install this product near maritime safety
equipment or other critical navigation or communication equipment
operating between 0.45-30 MHz.
REV081115