Cleaning & Maintenance - Guardian Technologies AC9200 Instrucciones De Uso Y Cuidado

Ocultar thumbs Ver también para AC9200:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATING INSTRUCTIONS
IMPORTANT: REMOVE ALL BAGS FROM FILTERS BEFORE FIRST USE!
The air purifier is shipped with the filters stored in the filter compartment. The filters are shipped
in bags to prevent degradation. Remove filters then remove and discard bags. See page E-8 for
filter/replacement instructions.
Note: Proper filter and front panel installation is necessary for unit to turn on.
BEFORE OPERATING THE AIR PURIFIER
1. Select a firm, level and flat location for the air purifier.
* For proper air flow, locate the unit at least 1 foot from any wall or furniture.
* Make sure none of the grills are blocked.
2. Plug the power cord into a 120V AC outlet.
3. When moving the air purifier, always lift it by the carrying handle.
OPERATING THE AIR PURIFIER
1. Turn unit power ON. The control panel power lights will turn on.
Note: The corresponding control panel lights will turn on depending on features selected.
2. Select fan speed MODE 1 - 3
1 = low, ultra quiet sleep mode
2 = medium speed
3 = high speed maximum allergen control (both 1 & 2 lights will be lit at this speed)
UV Bulb Replacement Indicator: The "UV" light on the display will flash when it is
time to replace the UV bulb. Replace the bulb according to instructions (E9). Reset
the UV light according to the "Reset Indicator Light" instructions (E8).
3. Select UV-C or Ionizer ON/OFF:
1. Press button once: UV-C On
2. Press button twice: Ionizer & UV-C On
3. Press button third time: Ionizer On
4. Press button fourth time: both Off
4. Timer/Unit Sound
1. If you prefer to run the purifier for a specific number of hours, you can select 2, 4,
or 6 hours by pressing the button. (At 6 hours, both the 2 & 4 hour lights will be lit.)
2. If you want to turn off the beeping sound of the buttons, hold the timer button for
a minimum of 5 seconds. Hold again to turn the sound of the buttons back on.
Note: The sound will remain off even if the unit is unplugged, and plugged back in.
*Filter Replacement Indicator Light: The REPLACE FILTER light on the control panel
will illuminate indicating that it is time to replace your filter. Replace the filter. Reset the
filter light according to directions (E-8).
E-6
OPERATING INSTRUCTIONS
RESETTING THE AIR PURIFIER
The air purifier is equipped with a motor protection device. If activated, the overload warning
indicator will initiate and cut off the power. An audible warning "ding" will sound 30 times over
15 seconds. To restart the unit unplug the unit then plug back in and power on.
Note: If the unit continues to shut down, there may still be an abnormal condition and the unit may
need service. Call Customer Service.
CLEANING & MAINTENANCE
CLEANING
Always unplug the appliance before you clean it.
Never immerse the appliance in water or any other liquid.
Never use aggressive or flammable cleaning agents such as bleach or alcohol to clean any part of
the appliance.
BODY OF THE APPLIANCE
Regularly clean the inside and outside of the body to prevent dust from collecting on the inside
and outside.
1. Wipe away dust with a soft dry cloth from the body of the appliance.
2. Clean the air inlet and the air outlet with a soft dry cloth.
PRE-FILTER SCREEN
The pre-filter is designed to collect larger dust and debris and should be cleaned monthly or more
frequently depending on use. Remove and clean regularly with the brush attachment of your
vacuum cleaner. This will remove the lint and dirt and help maintain the life of the filters. (See filter
replacement to locate and remove Pre-filter).
E-7

Publicidad

Tabla de contenido
loading

Tabla de contenido