Commissioning - Modular GWD 40 DT Serie Instalación, Uso, Mantenimiento

11. COMMISSIONING

Supply voltage through the main switch upstream
from the appliance, the machine is in standby
-
recognizable from the lit decimal points in the
displays of the tab control.
- Turn the water tap on.
Make sure that the filter and the overflow are
-
placed in the correct position.
Close the door or hood and press button P6 for at
least 2 seconds, to exit from standby status and
-
enter in working status. The machine starts filling up
with water and possible detergent.
Once the machine has been loaded the status green
-
light will lit (machine ready).
The boiler heating elements automatically come
into effect followed by the bowl heating element
once the boiler temperature (85°C) has been
reached.
Once reaching the temperature of 55° C., in the
bowl, the operation cycle can be started.
WARTER FILLING
DISHWASHING MACHINES
Atmospherical dishwashing machines have a
different filling and heating up of the bowl's water.
First of all boiler will be filled and when the correct
- water level will be reached water heating up will be
starting up to a temperature of 75°C.
After heating the machine will start to fill warm
water in the bowl for 20sec. If reached level won't
-
be correct the machine will be starting working as
per point 1.
This procedure will last up to required water level
- in the bowl will be reached. After that the green led
light goes on (status led) and there will be a beep.
The rest of the functioning operations are the same
-
as for pressure machines.
DEMARK: For best washing results it is advisable to
wait for the achievement of temperatures above
(indicated in the display).
IF IT IS NECESSARY TO OPEN THE
DOOR WHEN THE MACHINE IS
RUNNING AVOID DOING IT TOO
QUICKLY.
Although the appliance is equipped with a safety
switch to prevent the door from opening suddenly,
spurts of water could still reach the user in the
event of a hasty manoeuvre.
BY ATMOSPHERICAL
NORMAL OPERATING CYCLE:
Once the machine is ready to operate as per the "
COMISSIONING" paragraph, follow the instructions
below to run the desired wash cycles :
Insert the rack with the soiled crockery and close
-
the door;
Select the preferred cycle pressing one of the
-
buttons P1, P2 or P3.
(The end of the wash cycle is indicated by the green
-
" Status LEDs " and a beep).
Open the door, extract the rack with the clean
crockery and insert another rack, which has been
-
previously loaded, into the dishwasher for the next
wash cycle.
At least twice a day, or if you notice turbidity and
thickening of the washing water due to excessive
concentration of dirt particles in suspension, it is
ESSENTIAL to renew it.
Washing in these conditions causes wasteful
increasing of detergent and energy, to the
detriment of the quality of washing.
DRAINAGE PUMP
The exceeding water which enters the bowl at the
start of a rinse cycle is automatically drained.
Follow the instructions below to drain the bowl
completely:
- Remove the overflow (not the filter)
Press button P4 to start the draining cycle. The bowl
- sanitizing cycle follows the discharge cycle only
when hood is closed.
At the end of the cycle if you do not select any
- function the machine after 2min enters into
standby mode.
At this point you can remove the filter tank for
-
cleaning.
In models equipped
decalcification system and drainage pump, the
water is automatically drained from the bowl during
the regeneration cycle.
DECALCIFICATION AND REGENERATION OF RESINS
Some dishwasher models are equipped with a
system for water
regeneration of ion exchange resins in salt water.
DECALCIFICATION : the system is designed for
decalcifying the inlet water that runs through the
boiler (without any external intervention).
REGENERATION OF RESINS: a regeneration of ion
exchange resins in the water softener is required at
regular intervals depending on the hardness of the
inlet water (see table) and must be carried out as
follows:
22
with an inlet water
decalcification and the